HDMI Connection.

pledgeX

Ignore, mis-read post!

Toxteth_OGrady

joe134 wrote: »

then the i-can page comes up, with icons, press ok, it should auto tune,

When the i-can page appears are you waiting until the screen explaining the main use of arrow buttons appears before you are pressing ok on the remote?

joe134

Toxteth_OGrady wrote: »

When the i-can page appears are you waiting until the screen explaining the main use of arrow buttons appears before you are pressing ok on the remote?

I have tried both ways,
1;pressing immediately, because it,s only on a second, then it goes back to standby, and same happens if I leave it alone, the screen disappears, then standby again.

Toxteth_OGrady

Have you tried this when it goes back to standby:

1. Press the OPERATE button on the Remote Control Unit.

2. Make sure the Remote Control Unit is active.

3. if the LED is blinking when the remote is in use try to: Remove batteries, Press repeatedly the buttons, Leave the remote control for a couple of minutes, Insert the batteries

4. Turn the receiver off and on.

5. Unplug the power cable for 30 seconds and plug it in.

6. Follow the instructions above for frozen channels.

joe134

Toxteth_OGrady wrote: »

Have you tried this when it goes back to standby:

1. Press the OPERATE button on the Remote Control Unit.

2. Make sure the Remote Control Unit is active.

3. if the LED is blinking when the remote is in use try to: Remove batteries, Press repeatedly the buttons, Leave the remote control for a couple of minutes, Insert the batteries

4. Turn the receiver off and on.

5. Unplug the power cable for 30 seconds and plug it in.

6. Follow the instructions above for frozen channels.

yes, that,s what the manual says, but , there,s no operate button, presume, that,s tv on/off button..Don,t know wht they refer to words that are not on show;;;it,s confusing enough:eek:

Toxteth_OGrady

It's the "STB" power button on the top left of the digibox remote. Not looking good though!

You could try a live chat with i-can support:

https://retail.trc.adbglobal.com/

joe134

Toxteth_OGrady wrote: »

It's the "STB" power button on the top left of the digibox remote. Not looking good though!

You could try a live chat with i-can support:

https://retail.trc.adbglobal.com/

There is no above for frozen channels, there,s no channels to freeze. I think it looks like a return.I willtry the link, I,m going to get one from Argos, just down the road, and try that on it, see what happens, only basic box , 315 dearer, no leads, use this lead, if it works, just return it.
The reviewsall were down to user use, but, I thought mine would be ok, :rotfl:

joe134

joe134 wrote: »

There is no above for frozen channels, there,s no channels to freeze. I think it looks like a returnII,m going to get one from Argos, just down the road, and try that on it, see what happens, only basic box , 315 dearer, no leads, use this lead, if it works, just return it.
The reviewsall were down to user use, but, I thought mine would be ok, :rotfl:

I tried to set up the live link, they want to know all but your inside leg measurement, just to apply for login.

Toxteth_OGrady

joe134 wrote: »

There is no above for frozen channels, there,s no channels to freeze

It was referring to this;

My receiver is frozen on one channel, the LED blinks when pressing a button of the remote control but nothing happens.

Try the following procedure on the remote control:

1. Remove batteries

2. Press the buttons repeatedly to ensure no buttons are stuck down.

3. Leave the remote control for a couple of minutes

4. Insert the batteries again and retry

If that fails, try cycling the power as follows:

5. Remove power feed to the receiver for 30 seconds

6. Plug it back to the receiver

7. Switch the receiver on

8. Try again.

Toxteth_OGrady

In the meantime I suppose you could plug the aerial lead directly into the TV and tune-in the built-in Freeview SD on the TV.