📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Small job no.1

13»

Comments

  • twopenny
    twopenny Posts: 9,499
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    I've looked thought and studied and when it not freezing and wet outside I'll set to.

    Think I can use a small chisel/punch to knock back some wood around the nails then pliers, some way to leaver the nails out.

    I should be able to get both bits of wood out and start from there 🙂

    I can rise and shine - just not at the same time!

    viral kindness .....kindness is contageous pass it on

    The only normal people you know are the ones you don’t know very well


  • Section62
    Section62 Posts: 11,955
    10,000 Posts Fifth Anniversary Name Dropper
    Forumite

    Unless you are very careful heated air from the heat gun will bounce sideways off the top surface of the wood and go in the direction of the door/frame.

    Focussing heat on the gap between the wood and paving blocks has a risk of the hot air going into the void below and affecting the cill.

    To avoid a possible expensive repair bill it would be best not to use any heat anywhere near the uPVC components. Once damaged there is not much you can do to repair uPVC without the repair skicking out like a sore thumb.

    The same applies with any hammering/sawing/drilling etc. One slip and you can have irreversible damage to deal with.

  • WIAWSNB
    WIAWSNB Posts: 3,914
    1,000 Posts First Anniversary Name Dropper
    Forumite
    edited 7 November at 7:36AM

    I'm not sure trying to dry out soaked and expanded timber using a heat gun or hair drier is realistic in any case, for the time it'd take.

    2'penny - which of the two pieces of timber is causing the issue? Which one is pressing/rubbing? Is the bottom piece pushing upwards into the bottom edge of the sliding door? Or is the top piece pushing sideways ditto?

    And what tools do you have in the chisel/pry-bar /clawhammer category?

    And in the bolster/cold chisel box?

    And - silly Q - do you have an angle-grinder, or know anyone who does?

  • Boohoo
    Boohoo Posts: 2,659
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite

    @WIAWSNB if the angle grinder used is to reduce the size of the paver that sticks out it would make a lot of mess and it could unseat the pace when cutting and could them make it a missile when it flies off.

    Remove the paver(OP doesn't want that) then reduced the size and reattach using what the OP used before.

    OP is going to remove some wood around nail's to try and remove nails 1st.

  • twopenny
    twopenny Posts: 9,499
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    No the angle grinder was my first thought 😄 and I can't remove the block. Took 6yrs to find something that would make them stay on! Now they are definitely ON.

    Think it's the bottom but could be both. It's a heavy door and not been maintained before I bought the place. But it's also a good and useful burglar deterrent 😉

    I'm not convinced I can get the old nails out and Google was no help for sanding wheels to go on my drill so the DIY store it will be.

    It's the trouble with getting old. You loose the friends with useful gadgets and skills which is why this forum has been so brilliant.

    Sun has shown itself for the first time in a week so I'll set to soon.

    I can rise and shine - just not at the same time!

    viral kindness .....kindness is contageous pass it on

    The only normal people you know are the ones you don’t know very well


  • WIAWSNB
    WIAWSNB Posts: 3,914
    1,000 Posts First Anniversary Name Dropper
    Forumite
    edited 7 November at 9:46AM

    Yes, my first suggestion was to angle-grind the end of the paver. Why? Because it's the obvious solution.

    No, it won't create a mess, 'least not much. And, no, that block will not become a missile. To grind off that end just requires the disc to be played across it a number of times - not in the least bit aggressive or brutal. If the block moves, then it wasn't stuck down remotely well enough in the first place, but since all you are doing it grinding off a surface, and not cutting into the block, then it's very little risk in any case - and of course goggles and gloves should be worn.

    However, it requires an angle-grinder. Do you have one?

    The second possible solution is to gently hammer a wood chisel or pry bar between the two planks of wood, starting at the visible end. You'll soon know if the first nail along is going to budge. If it does, you are almost certainly on the home straight - just keep hammering summat in there, and prying away. Separate the two - if that will then allow them to come out.

    The third method is to remove that end block. I know you don't want to do this, 2'penny, and I know you think it's well-stuck down, but almost certainly it'll pop off with some gentle repeated thumping.

    Anything will do - ideally a cold chisel, but a wood type is fine, or a large flat-blade screwdriver, or even a large nail. Set it against where the block meets the bed, and start some repeated taps with 'ammer straight in there. But not thumps, just tap-tap-tap. Work your way along the bottom edge. And back again.

    When it comes away, you should find the two surfaces will re-mate neatly, so it just needs a firm brushing down to remove all grit and loose bits, and a smear of StixAll will sort it.

    Before all this, tho', I think you need to consider how you will address the too-large timber pieces; how on earth are you going to make them slightly smaller?! Are you going to plane them?! Sand them?!! Dig away whatever they are currently sitting on? Hope that they will shrink when removed and taken indoors? I think you need an answer to that before you start anything else, and if the answer is, "Haven't a clue!", then perhaps call up your local friendly handyperson to do it all?

  • Section62
    Section62 Posts: 11,955
    10,000 Posts Fifth Anniversary Name Dropper
    Forumite

    Just going back to the start of the thread…

    To fill the gap between the paving and door sill and piece of wood has been put in by previous owners.. When it rains it swells making the door hard to slide.

    If the door is rubbing on the wood then you should be able to see scuff marks on the door, or wood, or both. There's nothing like that visible in the pictures you've posted, although they don't cover all angles so it doesn't mean there's nothing there.

    Rather than removing the wood completely, if you can find where the door is binding you should be able to pare enough of the wood away with a sharp wood chisel so the door no longer binds.

    However, as you've mentioned a possible issue with the door bearings/rollers, I do wonder whether the issue is with them causing the door to be stiff, and it is just coincidence you notice the problem more when the wood is wet. There's also an outside chance colder/wetter weather could make a bearing/roller problem worse than it is in warmer/dryer weather.

    So before doing anything drastic the next step should really be identifying exactly where on the pieces of wood the door is binding. If it isn't obvious, putting some chalk or wax crayon on any high spots of the wood helps because then you'd see if it rubs off the wood or is transferred onto the door frame. If you still can't see the contact point(s) then it more or less rules the wood out as the cause of the problem.

  • twopenny
    twopenny Posts: 9,499
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    Good point about identifying Section. I've got chalk so I'll give it a go.

    Unfortunately the bit of sun has gone and it's freezing fog outside so still not inclined to go and fiddle.

    The problem is it's exposed to the worst of the weather so cleaning etc is temporary. Don't mind that if the temporary is at longer intervals. I may just look for or try to make the equivalent of a spout brush to clean a few more inches into the runners. I get the feeling it's dirt and debris not helping but I need to be gentle with that.

    I can rise and shine - just not at the same time!

    viral kindness .....kindness is contageous pass it on

    The only normal people you know are the ones you don’t know very well


  • Boohoo
    Boohoo Posts: 2,659
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite

    I think you should remove the wood 1st so you can see if the door is rubbing on the wet wood or there is an issue with the rollers making the door hard to open or close.

    You should remove the door and have a good look but you said that's not possible.

    If you get the wood removed and as suggested use plastic decking instead of wood and then it won't cause any issues in the future

  • Oldernowiser
    Oldernowiser Posts: 29
    Fifth Anniversary 10 Posts
    Forumite

    Angle grinder with mortar rake disc (Amazon, Screwfix, under £10) would take the edge off that block.

    Steady chisel work or Multi-Tool (cheap mains powered from £32 -£40 as above) would allow you to shave a 45 degree edge along the timber down below the door edge.

★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 356K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.3K Spending & Discounts
  • 248.5K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.