📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Small job no.1

2

Comments

  • twopenny
    twopenny Posts: 9,499
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite
    edited 30 October at 8:01PM

    The underneath is the wet bit so I think that contortion is beyond me 😄

    Unlikely to get the block paver off. It took me years to find something that would make it fast.

    There is a rubber stopper on the top runner B.

    I think I'm going to have to drill it sufficiently to break it up. Trouble is, the way to remake it using standard wood it would be standard size and then how to get it in.

    I did try using wood oil on it thinking it would soak in and repell water. It didn't. I wonder if 3 in one oil would?

    Or a small grinding wheel like this to shave some wood off.https://m.media-amazon.com/images/I/81eNfbFN-GL.SL1500.jpg

    I can rise and shine - just not at the same time!

    viral kindness .....kindness is contageous pass it on

    The only normal people you know are the ones you don’t know very well


  • Section62
    Section62 Posts: 11,955
    10,000 Posts Fifth Anniversary Name Dropper
    Forumite

    I will find out how much it will cost to get the door out because I think the bottom wheels? Ball-bearings? Are in need of replacement.

    If the door needs to come off for wheel/roller repair then I'd just wait until then to remove the wood, because with the door off you should just be able to lift the wood out.

    Options involving drilling/sawing/grinding all risk doing accidental damage to the door and/or frame.

  • Martin_the_Unjust
    Martin_the_Unjust Posts: 1,117
    Sixth Anniversary 1,000 Posts Name Dropper
    Forumite
    edited 30 October at 8:07PM
    1. Remove wood using hammer and chisel to break it up and throw it away.
    2. Buy a length of composite decking, cut it to size and glue (with no more nails or similar suitable for outdoor use) in place.

    You may need a couple of layers of decking to fill the depth.

  • twopenny
    twopenny Posts: 9,499
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    It's rock hard and nailed very securely.

    Has to be the only proper bit of workmanship in the whole thing 🙄

    Haven't even tackled the porch floor which is just a board screwed in. I haven't dared look under there!

    I can rise and shine - just not at the same time!

    viral kindness .....kindness is contageous pass it on

    The only normal people you know are the ones you don’t know very well


  • Boohoo
    Boohoo Posts: 2,659
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite

    So you have never removed the wood since you have lived there?

    It would not be nailed to the plastic cill but I bet it's screwed into the cill through the lower larger bit of wood and the top piece was nailed on top.

    You need to remove the top bit of wood using a claw hammer to get the nails out and a chisel maybe to remove the wood by the nails so the claw hammer can get access to the nails.

    You maybe able to jemmy the top wood off on the right hand edge as the wood looks rotten.

    Plastic decking is a good shout as replacement.

    If that doesn't work take the door off as mentioned before.

  • kipsterno1
    kipsterno1 Posts: 607
    Part of the Furniture 500 Posts Name Dropper Combo Breaker
    Forumite

    Do you have access to a drill and some wood bits? If you do you could remove the top piece (if you can't prise it off drill a circle of holes around each nail head). Once off drill a series of holes along the edge by the pavers. Be careful to ensure the drill doesn't catch the cill. Try and join these holes together but don't worry if you can't as it should be easy enough to saw or chisel through what's left. It should then slide past that lip.

  • twopenny
    twopenny Posts: 9,499
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    Now that's an interesting thought 🙂

    And it's given me another idea too. I can envisage a couple of tools that would fit on a drill that might do the job but don't know what they are called or if I can find them.

    I'll make a journey to the hardware shop, the old fashioned type that has everything, and see what's available.

    The job is on hold for the moment because of brisk north easterlies and damp then I'll settle down outside and see what works 😊

    I can rise and shine - just not at the same time!

    viral kindness .....kindness is contageous pass it on

    The only normal people you know are the ones you don’t know very well


  • Boohoo
    Boohoo Posts: 2,659
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite

    A circular saw set to just over depth about 10mm from the pavers and when done the whole length it may let you remove the bit you just cut.

    Or a multi tool and do the same as I suggested.

    I did suggest last about removing some wood around the nails and use a claw hammer to take the nails out.

  • FreeBear
    FreeBear Posts: 18,926
    Part of the Furniture 10,000 Posts Name Dropper Photogenic
    Forumite

    Do NOT use a hot air gun anywhere near uPVC unless you want a molten blob. Even a hair drier is likely to damage the surface of uPVC.

    Any language construct that forces such insanity in this case should be abandoned without regrets. –
    Erik Aronesty, 2014

    Treasure the moments that you have. Savour them for as long as you can for they will never come back again.
  • I did not say use the heat on the PVC only on the wood next to the block paving.

★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 356K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.3K Spending & Discounts
  • 248.5K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.