How set SKY remote fot HANNspree TV ?

GunJack

I personally don't like using the sky remote to control the tv, it doesn't do everything the tv remote will do, and therefore why "trade down" to using the sky for the tv ????

benny326

Just had sky+ installed, read several post's on various forums regarding the code for the remote operating a Hannspree tv. If anyone is still looking for a code to try, use 0206 it worked for me!! Sweet!!:j:j

burntbacon

benny326 wrote: »

Just had sky+ installed, read several post's on various forums regarding the code for the remote operating a Hannspree tv. If anyone is still looking for a code to try, use 0206 it worked for me!! Sweet!!:j:j

Yes! Thank you Benny326 - 0206 worked for me too, on my Hannspree Vibe 32" TV.

tammigirl

does anyone know a code that will work with a mirai telly please?

ratts

ahll wrote: »

Hi,
I have just got SKY installed today and I tried to set the remote so I can turn the volume etc up and down for the TV.

However it gave me a list of TV makes but I couldnt see HANNspree on the list ! I have a HANNspree JT02-37E1-000G LCD TV should I be looking for a different name in the list ? Or can some please tell me how I can set my remote up to also work the tv ?

Thanks

i got the same tv and the code i used is 0905 .......

follow the instructions (remote control setup) from your sky book,

but miss out number 4

that should sort you out

mamore2005

:TTry using any Bush model then use 0206 code.

simch

DatabaseError wrote: »

Programming your Sky remote control
The remote control can also operate the basic TV functions (Channel changing / volume control / Text etc) on around 90% of TV manufacturers.
The 4 digit code (Shown in your Sky handbook) is used to identify the make and manufacturer of your TV.
The individual 3 digit codes are used for each manufacturer.
To program using the 3 digit code.
1) Switch on the TV set
2) Press the TV button on the Sky Remote
3) Hold down the select and red buttons for 2-3 seconds until the LED blinks twice
4) Enter the 3 digit code
5) Press the select button to store Press TV and any number to test,
If this does not operate the TV set try below. To program using the 4 digit code
1) Switch on the TV set 2) Press the TV button on the Sky Remote
3) Hold down the select and red buttons for 2-3 seconds until the LED blinks twice 4) Press the TV button on the Sky Remote again
5) Enter the 4 digit code for your make of TV
6) The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7) Press the standby button on the Sky Remote (The TV should go to standby)
8) Press select to store this setting If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful. This will scan the codes used for a particular make of TV.

Awesome, I have been stuck with my Hanspree, but this "scanning" technique worked! It's a 19 inch hanspree LCD, new model and I started with a rev 9 remote, (new) entered 0056, nothing on the standby button, so tv standby, tv standby, kept doing it, about 15 times or so and suddently it turned off! pressed select to store and BINGO!!

Only toruble is I dont know what code it actually is, but it works and can always do it again!

cheers v much!

Moneymaker

The blink back method described by SatCure will tell you the code that you stored.

NiVZ

You can find most Sky remote codes at the bottom of the official Sky page:

http://www.sky.com/helpcentre/tv/remote-controls/operate-tv-with-sky-remote/

For Hannspree it says to try the following codes:

1773
1379
1376

NiVZ

rmwhall

i have just bought a Hanspree sj28dmbb and managed to find the code 0206 for a Sky+ Rev 8 remote.

Worked first time!

i hope this helps.