📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Spirit Level - differing results

2

Comments

  • EssexExile
    EssexExile Posts: 6,701
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    Use the spirit level both ways round then take an average.

    Tall, dark & handsome. Well two out of three ain't bad.
  • rob7475
    rob7475 Posts: 1,016
    Part of the Furniture 500 Posts Name Dropper Combo Breaker
    Forumite

    It can't be cost effective buying a big jar of bubbles like that though. I'd never get through them all. Can you not buy single bubbles or at least a smaller jar of them? 😉

  • Section62
    Section62 Posts: 11,955
    10,000 Posts Fifth Anniversary Name Dropper
    Forumite

    That's like wanting to buy just one stripe, instead of a whole tin of tartan paint.

  • Mutton_Geoff
    Mutton_Geoff Posts: 4,102
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite
    Signature on holiday for two weeks
  • bjorn_toby_wilde
    bjorn_toby_wilde Posts: 1,169
    Part of the Furniture 1,000 Posts Photogenic Name Dropper
    Forumite

    In theory the laser should be the most accurate because it self levels. Whether that’s true of all laser levels I don’t know. Mine is bang on.

    I agree with @stuart45 about Stabila. I had the same issues as you many years ago with a Stanley level. I binned it and bought a Stabila which is perfectly accurate even after years of use.

  • Section62
    Section62 Posts: 11,955
    10,000 Posts Fifth Anniversary Name Dropper
    Forumite

    In theory the laser should be the most accurate because it self levels. Whether that’s true of all laser levels I don’t know.

    Depends on the type of level.

    With some the laser is fixed in the body of the level and you have to manually adjust the level (usually with a bubble) to get the beam level (it sounds like the OP has this type). With others the laser 'floats' within the body of the level, and so long as the level is near-level, the beam will automatically adjust to true level. These may have a bubble on them because the level has to be manually adjusted to get within the self-levelling range.

    In terms of accuracy, provided it is adjusted/calibrated properly, a bubble level is as accurate as you need for building work. There are different grades of vial which are more or less sensitive - old school theodolites have a very sensitive bubble vial in the horizontal plane in which the bubble can move from end to end with a barely perceptable change in how level the base appears to be. Cheap levels often have thick graduation lines set much further apart than the length of the bubble, making it difficult to tell when the bubble is in the middle (the OP's red one being an example of this). The 'thickness' of the laser beam limits the accuracy of laser levels over short distances, but over longer distances a good laser (correctly calibrated) does a better job than a bubble level.

  • stuart45
    stuart45 Posts: 5,433
    Eighth Anniversary 1,000 Posts Name Dropper
    Forumite

    A water level takes some beating for accuracy.

  • Heedtheadvice
    Heedtheadvice Posts: 3,139
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite

    Also long level will give better results than a shorter one (AOTBE) as small imperfections in the wood surface exaggerates things that are ok over longer distance. As a example a 1mm bump in 100mm will look at worse than over 2.5m !

  • FreeBear
    FreeBear Posts: 18,926
    Part of the Furniture 10,000 Posts Name Dropper Photogenic
    Forumite

    There are different grades of vial which are more or less sensitive - old school theodolites have a very sensitive bubble vial in the horizontal plane in which the bubble can move from end to end with a barely perceptable change in how level the base appears to be.

    For really sensitive levels, take a look at some of the Starrett offerings - Sensitive to 0.02mm over a 1m length..

    I used something very similar to level the worktops in my kitchen. Just standing in the wrong place on a suspended timber floor is enough to get the bubble to move.

    Any language construct that forces such insanity in this case should be abandoned without regrets. –
    Erik Aronesty, 2014

    Treasure the moments that you have. Savour them for as long as you can for they will never come back again.
  • stuart45
    stuart45 Posts: 5,433
    Eighth Anniversary 1,000 Posts Name Dropper
    Forumite

    I was building a wall in a factory years ago, and when i came back from a break one of the factory mechanical engineers asked me how accurate a bricklayers level is. I told him that a Stabila is about 0.5 per metre, although after being knocked about a bit and dropped off the scaffold a few times a lot of them are a bit more out than that. He said that out of interest he stuck his engineers level on the wall it was miles out. When I put mine on it was plumb and level. He reckoned his short level was accurate to 1 thousandth of an inch over it's length. I explained to him that in the bricklaying trade if we worked to those sort of limits it would take a long time to put a house up. It was hard for him to get his head around the limits we worked when he'd spent his working life in thousandths of an inch.

★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 356K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.3K Spending & Discounts
  • 248.5K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.