Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Spirit Level - differing results
Hi,
I was hoping someone could help solve this mystery.
I have an issue where by my spirit level gives me a reading on one side and if I flip it, it gives a different reading.
I am trying to plumb a door frame.
I have attached a picture of each side of my original silver 1,800mm Magnusson aluminium boxed one. I get different results when I flip it - both sides are not plumb. For some reason I have never trusted this spirit level.
To see if I got a different result I bought a cheap red 1,800mm Forge aluminium boxed. I get different results when I flip it - one side it says it's plumb and the other side says it's not plumb.
I seen a YouTube video where you mark a line on a wall. However I was struggling to get this accurate trying to line up the original pencil line, when I flip the level over.
I have a laser level but I feel as though I get different results again!! I am not the best at lining up the laser.
I feel truly useless!
Thanks
Frank
Comments
-
-
The difference is so slight I wouldn’t worry about it.
2 -
3 and 4 appear to be matching. The two reds disagree when you flip
The photos are also taken at a slight angle which will change where the bubble appears to be sightly
1 -
Cant see a problem 3 & 4 are identical.
0 -
I have an issue where by my spirit level gives me a reading on one side and if I flip it, it gives a different reading.
When you say 'flip it' - do you mean end to end, or just face to face?
Spirit levels typically have only one face (the part in contact with your door lining) which will be accurate for a given adjustment of the vials. Even 'I'-section levels are rarely completely accurate on both faces, because that would require the faces to be perfectly parallel.
If the vials are adjustable it is best to pick one face (usually the unpainted* one for single-faced levels) and use only that one having tested/adjusted it for accuracy by flipping the level end-on-end.
(*If both faces are painted then the level probably isn't designed to be very accurate.)
3 -
They aren't far out for cheap levels. I've always used Stabila levels, which are more accurate. The bubble touches both lines. To test a level it's easier to use 2 screws and adjust them to get a level and plumb reading.
3 -
You can also check the lining with a plumb bob. Fix a screw at the top and drop the line down. You can then measure to check for plumb. Inside the line won't be affected by the wind. Outside you sometimes need to drop it into a small bucket with some heavy oil in.
2 -
Probably about 2-3mm which is a lot in a door lining.
0 -
-
How I have always done it is put the level on a surface (ideally a level one) and observe the bubble and notice where it is, now turn the level around and if the bubble isn't in the same place, it is not perfect
1
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards






