📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Failed fibre entry brick plate

When OR installed my fibre they used one of those plastic brick covers over the entry point with loads of silicone but I did notice it was quite warped and sure enough after many months it's finally given up the ghost and fallen off.

Is it a waste of time trying to get someone out to fix it and should I just do it myself. Where would you get these plates from?

1000010060.jpg

Comments

  • dnpark38
    dnpark38 Posts: 546
    Part of the Furniture 500 Posts Name Dropper
    Forumite

    Internet, eg.

    https://www.ebay.co.uk/itm/198409472813?_skw=Open+Reach+brick+hole+cover&itmmeta=01KZH3JZ4S9G5AYCP65Y1E9CRV&hash=item2e32204b2d:g:XFAAAeSw2-dqJeTb&itmprp=enc%3AAQALAAABAGfYFPkwiKCW4ZNSs2u11xBP9cT3388dxsd0pAVLD8VNK5JO6Hyo%2FZ9DdCKg7glyxB64%2FX9gBPbxrCATRwEuZoo1B7burrwolv2aetNdGo3iSOgYUDjj1%2FEhDFuTJiB9wKp%2Fs4iQmjIRInddm97Uxb02lqj1ULjQlc28iJhwZuQbrjKllDCO7jLc8D18h2RYhe79vtHtar1yiIh7fgZqzoENYJn%2BuxQ5J7Fs%2Bv7l3oBZJKmaOitEBYhWUEML3MV2NSvb2YO0SL7wBssMjoIxA1z70%2Fs7673r53qJ%2FTtjI2H2ZypIZzFurnLiJ4skcDahjCQeGrP3k5F0jXuSwDQTyuA%3D%7Ctkp%3ABk9SR87yy6P8Zw

  • flaneurs_lobster
    flaneurs_lobster Posts: 12,982
    10,000 Posts Seventh Anniversary Photogenic Name Dropper
    Forumite
    edited 8 August at 4:43PM

    Or the same link

    https://www.ebay.co.uk/itm/198409472813

    Has the old one broken?

    Could it not be screwed into place with a bit of drilling/Rawlplugging?

  • Rodders53
    Rodders53 Posts: 3,026
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    You can get the covers in Brown which might look better. It may even look better with the cover removed and silicon tidied up!

    DIY: Your ISP is unlikely to pay to get someone out to do it "many months" later.

  • EssexExile
    EssexExile Posts: 6,698
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    Can you not just re-affix it to the wall? There are holes in the corners for screws.

    Tall, dark & handsome. Well two out of three ain't bad.
  • shiraz99
    shiraz99 Posts: 2,026
    1,000 Posts Fourth Anniversary Name Dropper
    Forumite

    Thanks all. I'm getting a replacement from Screwfix tomorrow and some more clear silicone and will sort it myself.

  • Eldi_Dos
    Eldi_Dos Posts: 2,807
    Sixth Anniversary 1,000 Posts Name Dropper
    Forumite

    When fixing plate be aware not to compromise the bending radius of the fibre cable, by pressing down too hard.

    If I was to refit that cover I would use 3 rawplugs and screws with cup washers, leaving the bottom right hand corner free, so it did not put undue pressure on cable.

    It is worth spending a bit of time to do this rather than trying to secure with silicone which will only provide a temporary fix, as you have found out.

    Play with the expectation of winning not the fear of failure.    S.Clarke
★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 355.8K Banking & Borrowing
  • 254.9K Reduce Debt & Boost Income
  • 456.2K Spending & Discounts
  • 248.4K Work, Benefits & Business
  • 606K Mortgages, Homes & Bills
  • 179K Life & Family
  • 263.8K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.