Plumber using plastic flexi pipes in bathroom refit, is this ok?

Having my last bathroom refitted, all my sink pipes and radiator pipes are to be buried in the wall so not showing. He is using grey plastic flexi pipe to do this, is this ok or should I be worried, or is this ok?

Comments

  • Just had mine done the same way. Apparently plastic is the thing to use nowadays - no leaks - especially when under floorboards etc. Obviously the joints are crucial and I notice he used some metal joints but also they use sealant too to ensure there are no leaks. Plastic doesn't corrode so I suppose it's a logical step forward. However, for the new boiler they used the normal copper pipes - possible because of the high constant heat and pressure?
  • wallbash
    wallbash Posts: 17,775 Forumite
    He is using grey plastic flexi pipe to

    Its the modern way , and yes should have less joins/fittings.
  • loracan1
    loracan1 Posts: 2,287 Forumite
    Part of the Furniture Combo Breaker
    Same here, more noticeably the shower pipes because they're visible (but in a cupboard)
  • dori2o
    dori2o Posts: 8,150 Forumite
    Part of the Furniture 1,000 Posts
    It normally depends on the plumbers preference. Our kid hates using plastic and when he's hiding pipes in the wall simply uses copper with a plastic pipe around it.

    My mate who's a plumber loves plastic pipe as it can be bought on a coil and installed in long runs without the need for joints. and when a joint is needed it's simply a push fit/speed fit joint which has no need to be soldered in place.
    [SIZE=-1]To equate judgement and wisdom with occupation is at best . . . insulting.
    [/SIZE]
  • rrf494g
    rrf494g Posts: 371 Forumite
    I'd be a bit concerned if the plumber was using sealant on push-fit joints -otherwise it's now a matter of taste. as an old fogey I'm slowly moving from copper tube to plastic. When burying in walls you need some expansion/contraction space even with plastic I think.
    regards
  • Canucklehead
    Canucklehead Posts: 6,254 Forumite
    Good morning: the OH uses copper with rare exceptions...helps if you know how to solder;)

    HTH

    Canucklehead
    Ask to see CIPHE (Chartered Institute of Plumbing & Heating Engineering)
  • ormus
    ormus Posts: 42,714 Forumite
    modern plastics are fine for hot and cold water, these days.
    the only exeptions are the tails to the boilers. they have to be in 22mm copper, for about a 1m.
    id rather bury plastic pipe in the walls, than copper pipes.
    Get some gorm.
  • iamcornholio
    iamcornholio Posts: 1,900 Forumite
    Plastic pipes are OK, but just remind your plumber to ensure that any required earth equipotential bonding should be maintained - many forget this
  • bootman
    bootman Posts: 1,985 Forumite
    I've been Money Tipped!
    Thanks everyone, feel reasured now
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 349.8K Banking & Borrowing
  • 252.6K Reduce Debt & Boost Income
  • 453K Spending & Discounts
  • 242.7K Work, Benefits & Business
  • 619.5K Mortgages, Homes & Bills
  • 176.3K Life & Family
  • 255.6K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 15.1K Coronavirus Support Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.