Using nomorenails type glue for airingcupboard?

Hello all,

Anyone who has ever read any of my posts in this section will know how completed rubbish at DIY I am, so much so that I try to stay out of the way of any electrical equipment such as drills.

However, I have a small space where my combi boiler is of approx 2.5 foot across and a foot deep, I would like to put some wooden shelves up (the ones with slats) to store my towels.

As per the subject content - rather than use a drill to screw these shelves in, could I use something like nomorenails, I want to glue the batons to the wall and then slot the slats on these batons.

Is this feasible or is it asking for an airing cupboard collapse?

Thanks :)

Sou
«1

Comments

  • no u need to use screws.
  • fiddiwebb
    fiddiwebb Posts: 1,806 Forumite
    Do it the old fashioned way......with a screwdriver.
  • mcjordi
    mcjordi Posts: 4,238 Forumite
    Part of the Furniture Combo Breaker
    drill it- wall plug then screw

    no nails is a right chew on as you have to hold it /brace it till it sets
    Sealed pot challenger # 10
    1v100 £15/300
  • macman
    macman Posts: 53,129 Forumite
    Part of the Furniture 10,000 Posts Name Dropper
    NMN will be only as strong as the wall you fix it to, same as screws and plugs would be.
    No free lunch, and no free laptop ;)
  • Soubrette
    Soubrette Posts: 4,118 Forumite
    fiddiwebb wrote: »
    Do it the old fashioned way......with a screwdriver.

    Don't I need to use a drill to drill the screwholes????? Just kidding - even I'm not that rubbish at DIY ;))
    mcjordi wrote:
    drill it- wall plug then screw

    no nails is a right chew on as you have to hold it /brace it till it sets

    How long does it take to set? I thought you'd just put it on, whack it against the wall for a few minutes and then it would finish setting on its own :o
    macman wrote:
    NMN will be only as strong as the wall you fix it to, same as screws and plugs would be.

    I think the wall itself is fine for support, I wondered if the NMN would be the part that wouldn't hold.

    Sou
  • macman
    macman Posts: 53,129 Forumite
    Part of the Furniture 10,000 Posts Name Dropper
    Yes, of course you'll need a drill to put the plugs in.
    NMN will set in 24 hours, but a batten should hold itself up after a few minutes.It will be as strong as the plaster you are fixing it to. If the plaster is weak, then you need to go into the brickwork (I'm assuming this is an outside wall?).
    No free lunch, and no free laptop ;)
  • Canucklehead
    Canucklehead Posts: 6,254 Forumite
    Soubrette wrote: »
    Hello all,

    Anyone who has ever read any of my posts in this section will know how completed rubbish at DIY I am, so much so that I try to stay out of the way of any electrical equipment such as drills.

    However, I have a small space where my combi boiler is of approx 2.5 foot across and a foot deep, I would like to put some wooden shelves up (the ones with slats) to store my towels.

    As per the subject content - rather than use a drill to screw these shelves in, could I use something like nomorenails, I want to glue the batons to the wall and then slot the slats on these batons.

    Is this feasible or is it asking for an airing cupboard collapse?

    Thanks :)

    Sou


    Good afternoon: check your combi's manual for requirements i.e. ventilation and sharing the compartment before you do anything.

    HTH

    Canucklehead
    Ask to see CIPHE (Chartered Institute of Plumbing & Heating Engineering)
  • Soubrette
    Soubrette Posts: 4,118 Forumite
    macman wrote: »
    Yes, of course you'll need a drill to put the plugs in.
    NMN will set in 24 hours, but a batten should hold itself up after a few minutes.It will be as strong as the plaster you are fixing it to. If the plaster is weak, then you need to go into the brickwork (I'm assuming this is an outside wall?).

    No, it's an inside wall.

    The combi boiler was put in the same cupboard space that the hot water boiler was in ie a small cupboard in the second main bedroom - as far as I can see there is no ventilation etc, it was just a straight swap canucklehead - I will check the manual though, thanks :)

    Sou
  • EliteHeat
    EliteHeat Posts: 1,382 Forumite
    Soubrette wrote: »
    No, it's an inside wall.

    The combi boiler was put in the same cupboard space that the hot water boiler was in ie a small cupboard in the second main bedroom - as far as I can see there is no ventilation etc, it was just a straight swap canucklehead - I will check the manual though, thanks :)

    Sou

    What he means is that most manufacturers specifically state that the cupboard housing the boiler may not be used for storage. Most owners specifically ignore this, so everyone's happy ;)
  • Canucklehead
    Canucklehead Posts: 6,254 Forumite
    EliteHeat wrote: »
    What he means is that most manufacturers specifically state that the cupboard housing the boiler may not be used for storage. Most owners specifically ignore this, so everyone's happy ;)

    Make that 'what she means'.:D

    Canucklehead
    Ask to see CIPHE (Chartered Institute of Plumbing & Heating Engineering)
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 349.8K Banking & Borrowing
  • 252.6K Reduce Debt & Boost Income
  • 453K Spending & Discounts
  • 242.8K Work, Benefits & Business
  • 619.5K Mortgages, Homes & Bills
  • 176.4K Life & Family
  • 255.7K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 15.1K Coronavirus Support Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.