Restore Laptop To Default Settings?

Luke90_2

Hey

I have an Advent 8115 Laptop, Windows Vista Home Premium.

I want to restore the laptop to it's default/original settings but I do not have the discs to do so - is there any other way I can do this?

Many thanks :beer:

crampo_2

normally you should have a program on your all program list to make backup discs. Might be under "Advent".

bainy

You can restore your computer back to factory settings by using the hard drive recovery located on a hidden partition on the hard drive.


To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions.

Hope this helps and you have a fully restored system once again.

Luke90_2

bainy wrote: »

You can restore your computer back to factory settings by using the hard drive recovery located on a hidden partition on the hard drive.


To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions.

Hope this helps and you have a fully restored system once again.

Wow thanks alot :beer:

Really appreciated that post and it helped me alot, so cheers!

mk_wotsit

Will this work the same on XP too?

badgerbuckets

Pressing F10 on system boot should take you to the inbuilt system restore option - then choose the option you want. To go all the way back to 'out of the box' condition, choose 'destructive method' - NOTE YOU WILL LOSE ALL DATA FROM THE COMPUTER. Anything you have on the pc, such as documents, pics, movies, music, etc will be lost permanently. All programmes installed since first use will also be lost. BACKUP to cd/dvd/online storage FIRST!:beer: