We'd like to remind Forumites to please avoid political debate on the Forum... Read More »
The Forum is currently experiencing technical issues which the team are working to resolve. Thank you for your patience.
Removing a telephone socket

goingsenile
Posts: 338 Forumite

in Techie Stuff
Hi
I've just had my kitchen redone and in it all forgot about my phone socket.only realised tonight now that the joiner has moved all his tools and the old phone, wires and socket were sitting on the window ledge (all still working)
This is not the main socket and I would ideally like to remove it as have cordless phones so don't really need it.
How do I get rid of it ( without paying BT fortune to send an engineer).
Bit of a problem getting into it now, wire from one side behind wall units and wires from other side behind granitite worktop!
Any one any ideas?
Thanks
AJ
I've just had my kitchen redone and in it all forgot about my phone socket.only realised tonight now that the joiner has moved all his tools and the old phone, wires and socket were sitting on the window ledge (all still working)
This is not the main socket and I would ideally like to remove it as have cordless phones so don't really need it.
How do I get rid of it ( without paying BT fortune to send an engineer).
Bit of a problem getting into it now, wire from one side behind wall units and wires from other side behind granitite worktop!
Any one any ideas?
Thanks
AJ
0
Comments
-
Just remove the box and cable back to the master socket or junction point. No need to get BT in, they are not concerned with anything your side of the master socket as it's your responsibility.No free lunch, and no free laptop0
-
Just remove the box and cable back to the master socket or junction point. No need to get BT in, they are not concerned with anything your side of the master socket as it's your responsibility.
Thank you for replying but I'm going to need the idiots guide here.
If for example. I cut the wires either side of the box, will that effect my other phones?
Sorry, not very DIY minded
AJ0 -
Careful there is 50Volts across two wires so don't cut them all at once it will short, cut each one at a time. There is a small current there but you could blow BT fuses somewhere then you won't have a phone. Go back to where the extension meets the incoming line and remove / disconnect from there. Really simply to do , good luck, 1 minute job.0
-
Or open master socket and remove wires 2 (blue) 3 (orange) and 5 (blue and white). OH is a bt engineer. Hth
Thrifty"A life spent making mistakes is not only more honorable, but more useful than a life spent doing nothing." George Bernard Shaw:p0 -
goingsenile wrote: »Thank you for replying but I'm going to need the idiots guide here.
If for example. I cut the wires either side of the box, will that effect my other phones?
Sorry, not very DIY minded
AJ
If there is one cable coming into and another leaving the box, then this is not a straighforward spur extension, it sounds more like it then continues on to another extension? So if you remove this one you might disconnect another.
Follow the cables from your master socket and work out what goes to where before you remove anything.No free lunch, and no free laptop0 -
Thanks to everyone for there replies- maybe this is not as simple as I though.
I'm going to look in yellow pages and see if there is a local telephone enginineer and see if they will come and look- sure it will be cheaper than BT
AJ0 -
Any DIY man or electrician can do this for you, it's no more complicated than wiring a plug.
If you have 2 cables from the socket, it must be wired in series with another extension. If one cable only, it must be wired either straight back to the master socket. or it is the last socket in the series.
If the former, removing it will disconnect another socket. If the latter, you can remove it without affecting anything else.
Usually the layout of your sockets in relation to the master socket will make it obvious which method has been used.No free lunch, and no free laptop0 -
Any DIY man or electrician can do this for you, it's no more complicated than wiring a plug.
If you have 2 cables from the socket, it must be wired in series with another extension. If one cable only, it must be wired either straight back to the master socket. or it is the last socket in the series.
If the former, removing it will disconnect another socket. If the latter, you can remove it without affecting anything else.
Usually the layout of your sockets in relation to the master socket will make it obvious which method has been used.
Hi macman
Thanks for your help. by the looks of things it is wired in series, which is where I'm concerned as I'd rather not disconnect my other connections.
I'll give my electrician a ring and see if he can do anything with it
Thanks again
Aj0 -
dont get ripped off!
find out what his call out charge will be first!
as said before it shouldnt take more than a couple of minutes......so dont get charged for an hour or mores labour, plus call out!!0 -
It literally is a case of 2 screws, pulling out a few wires and screwing up again.0
This discussion has been closed.
Confirm your email address to Create Threads and Reply

Categories
- All Categories
- 350K Banking & Borrowing
- 252.7K Reduce Debt & Boost Income
- 453.1K Spending & Discounts
- 242.9K Work, Benefits & Business
- 619.8K Mortgages, Homes & Bills
- 176.4K Life & Family
- 255.9K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.1K Discuss & Feedback
- 15.1K Coronavirus Support Boards