📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Help... New Pc, Old Hd

Ok so got new pc today, fitted g,card, ram etc and old hard drive.

started her up and good news, found the graphics card but after that and the bios loads i get a blue screen for a millisecond (not long enough to read it) then it restarts the pc, is this due to conflicting drivers on my old hard drive or something else?

and if it is, how would i go about removing these drivers without having to wipe the entire disk?


Thanks

Ben

Comments

  • smcicr
    smcicr Posts: 365 Forumite
    This could be a variety of things to be honest - could be bad ram, card issues and so on. I'd advise taking out everything other than graphics card (assuming it's AGP not PCI/Express so can only go in one slot?) and RAM and trying again. (This also means take out or disconnect any other hard drives or CD / DVD drives)

    If you have more than one stick of RAM try using different sticks (and in different slots) but do it all methodically so you know what you've tried :)

    The other thing is do you have the HDD at the end of the IDE cable and set either as Master or Cable Select with the jumpers on the unit?

    When there are so many possibilities it's just a case of cutting them down and slowly building up. Let us know how it goes.
    "Don't go around saying the world owes you a living. The world owes you nothing. It was here first." (Mark Twain)
  • benbfc
    benbfc Posts: 263 Forumite
    g card is agp so is fine.

    went into bios - Hard drive is IDE Master 0
    DVD RW is IDE Master 1


    havent seen anything to suggest the ram has been found yet.


    does that help!?
  • Joe_Bloggs
    Joe_Bloggs Posts: 4,535 Forumite
    You should try memtest86. This can boot from a floppy or CDROM image. You don't need your old hard drive to test your system out. In fact it would have been a good idea to test the system out without a hard drive if it contained valuable information.

    The post is completely void of any technical information, however, starting in safe mode is a very good way of avoiding driver issues. This may present an oppertunity to backup important stuff, get rid of old drivers and install new.
    J_B.
    PS you can often select a slower and more visible memory test as a bios option. This is not as comprehensive as memtest86.
  • smcicr
    smcicr Posts: 365 Forumite
    Have you tried switching the RAM around in the slots / just using 1 stick etc? As Joe_Bloggs says - you can also test the RAM with the above mentioned memtest86 and that would also be a good idea.

    The drives are fine - I was wondering if the HDD wasn't being recognised due to jumper or positioning issues but that sounds like it's not the case.

    Once you know that everything is working hardware wise then it's possible to move on to other areas.
    "Don't go around saying the world owes you a living. The world owes you nothing. It was here first." (Mark Twain)
  • Mr_Skint_2
    Mr_Skint_2 Posts: 5,183 Forumite
    Start up in the Bios to see if the HDD is being shown how many KB/mb.
    Just as a make sure.
  • lipidicman
    lipidicman Posts: 2,598 Forumite
    Who fitted the motherboard? I once had a PC with a fitting screw in the wrong place shorting out the MB. Just shows the problem could be anything!
This discussion has been closed.
★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 356K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.3K Spending & Discounts
  • 248.5K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.