Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
making patch cables ??
statman
Posts: 167 Forumite
in Techie Stuff
Can anyone advise - I am trying to reduce the length of a cat 5 cable. I tested the cable before cutting it and all 8 lights on my cable tester lit up. I put a new RJ45 on the cut end and I am now only getting 5,6,7and 8 lighting up? I have cut and redone it several times with the same result. All the wires are in line with the original RJ45.
Can anyone shed any light.
Feel really old fashioned as everybody else seems to be going wireless!!!!!!
Can anyone shed any light.
Feel really old fashioned as everybody else seems to be going wireless!!!!!!
0
Comments
-
This is just one of those tricky things that gets easier with practice. I would try again, and double check the wiring postitions. Have a look HERE to check your wiring
Old fashioned here as well! I've hardwired the whole house by burying the cables into the wall to RJ45 wall sockets. At least we don't have to worry about our neighbours connecting to our network!How many surrealists does it take to change a lightbulb?
...
...
...
...
Fish0 -
which colour sequence did you use? I have been matching the existing end that has w/orange, orange not w/green, green or does it not matter as long as they match up?
I have tried about 5 or 6 and keep getting the same 5,6,7,and 8 lights on the tester?0 -
If you are using a hub or router ..........both ends
1 orange/white
2 Orange
3 Green/white
4 Blue
5 Blue/white
6 Green
7 Brown/white
8 BrownHow many surrealists does it take to change a lightbulb?
...
...
...
...
Fish0 -
Rex_Mundi's pin-wire assignments above are correct for 568B which is the most commonly used wiring assignment.
However, picture's Rex linked to give 568A.
Technically it doesn't matter which one you use (or you could make your own up) as long as both ends are wired the same for a straight cable.
For a cross-over cable (computer to computer direct) one end needs to be 568A and the other 568B
Most people stick to 568B so use Rex's Pin-Wire assignment above.
Wiring network cables takes a bit of practice so don't lose heart.
Sometimes the cheap crimpers don't press all the connection pins into the wires evenly. Also check all the wires are reaching the end of the RJ-45 connectors.Hug provider for depression thread :grouphug:
"I'm not crazy, I'm just a little unwell.." - Unwell by Matchbox Twenty0 -
sorry, I went to bed! Created another end as per Rex and Blinky 568B, checked everything still no joy. First lot of connectors from B & Q, second lot from Maplins but same result with both 5,6,7 and 8 showing a connection!
Took the cable to a friends who used a fluke(?) to check the continuity and all were OK?
When you say don't lose heart?????????0 -
Are you sure your tester is working OK?
Cheers for pointing out the wrong link blinky. The problems with having multiple windows open..............I must have copied the wrong link. I've edited the link to the correct diagram now.How many surrealists does it take to change a lightbulb?
...
...
...
...
Fish0 -
Rex_Mundi - no worries mate.Hug provider for depression thread :grouphug:
"I'm not crazy, I'm just a little unwell.." - Unwell by Matchbox Twenty0 -
Some times the crimper compresses the spring clip whilst making the connections.You may have to bend it back outwards to later create some force on the connecting terminals when it is in a socket.
J_B.0 -
tester is fine as i have tested other cables that are all lighting up.
Could it have anything to do with the fact that one of the connectors is factory fitted (even though I can see the wiring is exactly the same as I have been doing the other end) so would it make a difference if I made up the other end?0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards