Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
TV, DVD, and NTL connections
Beez_2
Posts: 15 Forumite
in Techie Stuff
Can somebody help with an unusual problem with my NTL, TV, DVD Recorder setup.
My NTL box 'Out' is connected via SCART to my DVD Recorder 'In'
The NTL box is connected direct to TV (AV1) via SCART
The DVD recorder is connected direct to TV (AV2) via SCART
The DVD is also connected to the TV via Co-Axial
Everything works OK, the DVD can record all terrestrial channels and will record from NTL.
The problem I have is that I cannot switch between the NTL box and the DVD Recorder. When I had Sky it was a simple matter of switching between 'AV1' and 'AV2'. However with this setup I have to ensure that the DVD is turned off, otherwise I cannot see NTL. If I am viewing NTL and turn the DVD on then that is OK but if I view the DVD and then stop what I am watching I cannot get NTL back unless I switch the DVD to standby.
Interestingly if I do watch the DVD then the signal comes through the TV on both AV1 and AV2 even though the DVD is not directly connected to 'AV1'. When I turn the DVD to standby then the signal to 'AV2' disappears.
Any advice anyone can offer?
Thanks for listening
My NTL box 'Out' is connected via SCART to my DVD Recorder 'In'
The NTL box is connected direct to TV (AV1) via SCART
The DVD recorder is connected direct to TV (AV2) via SCART
The DVD is also connected to the TV via Co-Axial
Everything works OK, the DVD can record all terrestrial channels and will record from NTL.
The problem I have is that I cannot switch between the NTL box and the DVD Recorder. When I had Sky it was a simple matter of switching between 'AV1' and 'AV2'. However with this setup I have to ensure that the DVD is turned off, otherwise I cannot see NTL. If I am viewing NTL and turn the DVD on then that is OK but if I view the DVD and then stop what I am watching I cannot get NTL back unless I switch the DVD to standby.
Interestingly if I do watch the DVD then the signal comes through the TV on both AV1 and AV2 even though the DVD is not directly connected to 'AV1'. When I turn the DVD to standby then the signal to 'AV2' disappears.
Any advice anyone can offer?
Thanks for listening
0
Comments
-
probably wont work at all, but try swapping ur av1 and av2 scart leads round0
-
Try switching the order of them.
NTL TV(not VCR) out scart to DVD Recorder In
DVD Recorder out to TV AV1
NTL VCR out to AV2
Co-axial as it is
To see NTL whilst DVD recorder is switched on, make sure that DVD Recorder channel is set to AV2(whichever AV on the recorder the NTL scart is connected to). When the DVD recorder is off the signal will just pass through, or you can switch to AV2 if you need0 -
Woby_Tide wrote:To see NTL whilst DVD recorder is switched on, make sure that DVD Recorder channel is set to AV2(whichever AV on the recorder the NTL scart is connected to). When the DVD recorder is off the signal will just pass through, or you can switch to AV2 if you need
Have tried switching the SCART conections on the TV but no change. Not sure I understand 'make sure that DVD Recorder channel is set to AV2'. Can you clarify?
Thanks for help so far.0 -
See if there is a "TV/video" or "TV/DVD" button on your dvd remote- it may be giving it's signal a priorty message (which scart can do). Most DVD players do this so when you switch them on the TV switches straight to the DVD channel.0
-
Beez wrote:Have tried switching the SCART conections on the TV but no change. Not sure I understand 'make sure that DVD Recorder channel is set to AV2'. Can you clarify?
Thanks for help so far.
the DVD recorder is like a VCR in that you can choose to record from it's internal tuner i.e. channel 1/2/3/4 etc. but now NTL is connected via a scart so to record from NTL you would select the AV channel on the DVD recorder to record an NTL channel. Whilst the DVD is switched on, this channel you select is the signal that will pass through and on to the TV, try pressing 0 on the DVd controller if there isn't an AV button0 -
Thanks for advice from all - problem now sorted.
The DVD recorder connection for 'Satellite' acts as both input and output as does the 'Video' connection. The NTL engineer had connected the NTL box to the Video connection on the DVD, not the Satellite connection. Silly me to assume he knew what he was doing. Not easy to see though as the labels are obscured by the leads.0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards