Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
help with a shuttle system..
benbfc
Posts: 263 Forumite
in Techie Stuff
with my pc recently blowing up on me i have to get another 1 asap, i have graphics card, ram and a hard drive that are still fine and was thinking maybe of getting a small shuttle barebones system, just wondering if they are easy to set up and use? as although i am competant with installing ram and stuff, cpus etc would be totally new to me.
also the hard drive i put in will be my old one with windows already installed and all my music, photos etc on. is this a problem or do u just install it as normal?
if anyone can reccomend a good system then i am all ears too.
Regards
Ben
also the hard drive i put in will be my old one with windows already installed and all my music, photos etc on. is this a problem or do u just install it as normal?
if anyone can reccomend a good system then i am all ears too.
Regards
Ben
0
Comments
-
I personally, am not a fan of Shuttle cases. Some people do like them, but for the price you could get a decent case, more powerful psu, and a better (higher spec) motherboard. The advantage with a Shuttle case is that it's of small form factor.
Have a look at the Antec Sonata II, it's a great case and comes with a decent 450W psu. The build is great, it runs quietly (more so than a Shuttle) and it looks good. Retails at about £80.
You then just need to pickup a motherboard, and it'll probably work out cheaper than getting a Shuttle.
The Sonata gets plenty of top reviews:
http://www.legitreviews.com/article.php?aid=217&pid=1
http://www.neoseeker.com/Articles/Hardware/Reviews/rev_sonata2/
http://www.extremetech.com/article2/0,1697,1834322,00.asp
http://arstechnica.com/reviews/hardware/sonata.ars
and so on...
Microdirect.co.uk have the second version (Antec Sonata II) for £78.67"Boonowa tweepi, ha, ha."0 -
Sorry for butting into someone else's thread again (saves starting multiple threads on the same subject
) but I've been thinking of getting a new case with a better PSU and cooling qualities for my son's PC because of the recent over-heating problems. Would it be as simple as transferring everything over or would I risk damaging the mobo by removing it?
I built the original from scratch and fitted the mobo and everything else myself so I'm confident enough to do the swap over if it's a feasible job
"An Ye Harm None, Do What Ye Will"
~
It is that what you do, good or bad,
will come back to you three times as strong!
0 -
See my post above. The Antec Sonata is a great case for the price. I've used it before when building machines for friends, and it has all the build quality of my Lian Li and Silverstone case (which are £100+ each without psu). The Antec psu is very good too if you look up the specs.
It shouldn't be a problem at all. Just take the usually precautions, be patient, and make sure you are well earthed."Boonowa tweepi, ha, ha."0 -
@Curry_Queen
There is allways a risk of damaging the motherboard when moving it. Proper planning and preparation will minimise these risks. Make space for the work. Take anti static precautions As Wolfman says but be careful with the screwdriver, you could scratch through a track. Treat the motherboard like a precious dinner plate. Have some anti static foam place where you can put the motherboard down. You may have to add/remove supporting spacers in the new case. Some existing spacers may short out motherboard components if they are left in place. Get the hang of things on an old/unimportant PC if in doubt.
J_B.0 -
I've just finished building a shuttle - very well engineered and very quiet - which was the main reason for choosing this particular model
Note that some advertising is misleading this one would take 1 DVD drive and a floppy but you could not fit a second hard drive with the floppy installed
Only two PCI slots and frankly a bulky graphics card and fan would probably fill them both Similarly a bulky AGP card could stop you using either PCI slot. Most of them have nearly everything on board anyway
Other than that I thought it was good valueTANSTAAFL !0 -
Joe_Bloggs wrote:@Curry_Queen
There is allways a risk of damaging the motherboard when moving it. Proper planning and preparation will minimise these risks. Make space for the work. Take anti static precautions As Wolfman says but be careful with the screwdriver, you could scratch through a track. Treat the motherboard like a precious dinner plate. Have some anti static foam place where you can put the motherboard down. You may have to add/remove supporting spacers in the new case. Some existing spacers may short out motherboard components if they are left in place. Get the hang of things on an old/unimportant PC if in doubt.
J_B.
I've still got the anti-static foam and wrappings that the the mobo came in (I hoard useless things
) so that's not a problem, and I also have a variety of spacers and screws somewhere. I seem to remember that I had problems fitting the mobo originally as the instructions that came with it were slightly different to what I needed to do so ended up with plenty of spares!
The only part during building that PC that I found scary was actually fitting the CPU, which I won't have to do again thankfully, so this should be a breeze to do <touch wood>
I'm assuming that most new cases will happily accommodate the mobo, which I believe is an ASUS AMD without checking, and is less than a year old, or have things moved on and is there anything I should avoid buying?"An Ye Harm None, Do What Ye Will"
~
It is that what you do, good or bad,
will come back to you three times as strong!
0 -
You generally get a bag of screws and spacers with a new case. Make a note of where the 'jumper wires' that connected to the front pannel of the old case went on the motherboard. Typically reset, power on, hard disk light etc. They are probably labled for the old case but draw a diagram that can help remind you when you switch to the new case. Find your motherboard manual to check these header connections as a precaution.
I've still got my old motherboard boxes and they are stuffed with old cards in anti static bags, connectors, blanking plates etc.
Get some top quality heat sink compound you may need to use it as you will probably have to flip your Motherboard over many times to inspect the underside for potential fouling by spacers. This could ruin the possibly poor thermal contact with the heatsink at present.
J_B.0 -
Check out this weeks Micro Mart
http://www.micromart.co.uk/default.aspx?contentid=0a437af8-b1f5-4ffc-a6c8-f567007946de&featureid=2564
There is a shuttle article this week0 -
Joe_Bloggs wrote:You generally get a bag of screws and spacers with a new case. Make a note of where the 'jumper wires' that connected to the front pannel of the old case went on the motherboard. Typically reset, power on, hard disk light etc. They are probably labled for the old case but draw a diagram that can help remind you when you switch to the new case. Find your motherboard manual to check these header connections as a precaution.
I've still got my old motherboard boxes and they are stuffed with old cards in anti static bags, connectors, blanking plates etc.
Get some top quality heat sink compound you may need to use it as you will probably have to flip your Motherboard over many times to inspect the underside for potential fouling by spacers. This could ruin the possibly poor thermal contact with the heatsink at present.
J_B.
Ahhhh yes, you're bringing back memories of figuring out which wire leads to where and how they connected. I'm afraid my memory fails to retain stuff that I haven't accessed within the last week or so these days LOL! But thankfully, I'm quick to learn and can follow instructions
I was actually surprised at how relatively easy it is to build a PC (that was my first from complete scratch but I'd half-built the one I'm using now from a case that came with PSU, mobo and CPU already installed) and did consider taking it up as a business at one point, but my lack of technical knowledge if things go wrong and repairing PC's would be my downfall
"An Ye Harm None, Do What Ye Will"
~
It is that what you do, good or bad,
will come back to you three times as strong!
0 -
learn everything you need to know about Shuttle and Small Form Factor PC's from here.
https://www.sudhian.com0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards