📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Is This A Bodge Job (Roofing)

MrMeeples
MrMeeples Posts: 10
Second Anniversary Name Dropper First Post
Forumite

We had a local firm in (decent reviews on Checkatrade) to redo the lead flashing around our side of a shared chimney. Whilst up their they identified that the ridge tiles were just loose, with crumbled cement, as it's a 1960's house.

So they did new the flashing around front and side of the chimney, and reseated the back and back corner lead, and also installed a new ridge tile kit all along the top of the roof.

However, I personally think the flashing is a bit rough, and the roof ridge tiles seem to have a gap at the end. They reused the original tiles, but had to replace a cracked one at the end. Seems the new one was slightly larger, and as a result there's a gap (see photo). I'd like people opinion of the Flashing and whether or not the gappy ridge tiles is going to be an issue when it rains.

Am I being paranoid, or is this a sloppy job?

1 - DSC08518.JPG 2 - DSC08524.JPG 3 - DSC08535.JPG

Comments

  • Stubod
    Stubod Posts: 2,718
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite

    ..Sloppy with a capital S!!!

    .."It's everybody's fault but mine...."
  • Is that silicone they have used where the leadwork is fitted into the bricks? it doesn't look like cement.

  • stuart45
    stuart45 Posts: 5,433
    Eighth Anniversary 1,000 Posts Name Dropper
    Forumite
    edited 17 November at 6:36PM

    Most plumbers or lead workers use something like Lead mate nowadays instead of sand/cement.

    The work is rough though. Have a look at some of Peter Scholey's videos to give you an idea of how it should be done. This is one of a few he has made. Step Chimney Flashing 2

    The front apron on your chimney looks like it's 2 separate pieces of lead. Fitting Chimney Flashing front apron

  • MrMeeples
    MrMeeples Posts: 10
    Second Anniversary Name Dropper First Post
    Forumite

    Unfortunately the neighbours could not afford to have their side done, and ours was leaking badly. So we were forced to just do our side. I guess it's good that the back lead was not replaced, as it was all one piece.

  • UnsureAboutthis
    UnsureAboutthis Posts: 843
    500 Posts Third Anniversary Name Dropper
    Forumite
    edited 18 November at 9:41AM

    Hi pal

    Its not tidy, not sure how much he has cut into the cement. Though I'm no roofer, far from it, we've had a food roofs done inc chimneys.

    IMO, the overlap onto the roof tiles, he has left a decent amount as years ago, 35+ yrs ago we had our first roof done when we moved into our new home, the building regs worker made the guy pull of the flashing as there was insufficient amount - that's how I know.

    I guess it takes a lot of experience/skill to do a tidy/good job

    A roof we had done about 4 years ago - I asked the roofer why he had not cemented the ridge tiles - it turns out some of the new ridge tiles are screwed/clipped in, so got no motar in ridge tiles - just up the road, tiles look the same they have it - However, roof is 4+ yrs old, no probs so far.

    I hope this helps.

  • stuart45
    stuart45 Posts: 5,433
    Eighth Anniversary 1,000 Posts Name Dropper
    Forumite

    UnsureAboutthis wrote I guess it takes a lot of experience/skill to do a tidy/good job.

    The problem in the private sector is that in the trade on site lead work is done by the plumbers who were properly trained at Tech in lead work. In recent years a separate trade of lead workers has been brought in because a lot of plumbers weren't interested in getting up on the roof to do it.

    In the private sector it's normally roofers who people turn to for flashing work, partly because they think they were trained for the work, and partly because they are the only ones they can find with the equipment to get up on the roof. I do know some roofers who can do a reasonably good job with flashings, although in general they are nowhere near as good as a traditional plumber or lead worker. The word plumber comes from the Latin word for lead.

  • stuart45
    stuart45 Posts: 5,433
    Eighth Anniversary 1,000 Posts Name Dropper
    Forumite
    edited 18 November at 12:06PM

    You can buy ready made lead half front aprons for this purpose, but you need to make sure the joint is weatherproof.

    Lead Half Front Chimney Apron – Left or Right Hand - Custom Lead

  • EssexExile
    EssexExile Posts: 6,701
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Forumite

    The flashing is rough but it will probably work fine, the ridge tile looks ok.

    Tall, dark & handsome. Well two out of three ain't bad.
★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 356K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.3K Spending & Discounts
  • 248.5K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.