Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Anyone recommend a torque wrench...
That measures torque CCW direction, either 1/4" or 3/8" ".
Not looking for an expensive instrument as it's not going to see much action.
Comments
-
Look for one with a push-through 1/4 or 3/8 bar?
was the first 'bidirectional' tool I found under a £200 price tag… Amazon etc.,. may well have others at a lower price.
Google and A I ought to find many more with time and patience…
Don't forget to check the instrument has the torque-setting range you need for the fasteners concerned.
1 -
Aldi / Lidl often have them. Good enough for the majority of heavyish jobs, all depends on what you want to use it for.
Never associate with idiots on their own level, because, being an intelligent man, you'll try to deal with them on their level - and on their level they'll beat you every time.
Being hated by idiots is the price you pay for not being one of them.
Jean Cocteau 1889-1963
0 -
Not a recommendation…
0 -
I bought a couple of Uharbour torque wrenches from Amazon for motorcycle work. I needed precise low and high torque for clutch and flywheel reassembly.
1x 3/8" 5 - 60Nm and 1x 1/2" 20 - 230Nm gives the torque needed and avoids having to use extreme ends of their range. Bi directional via a switch and good value. 1/4" drive also available for low torque jobs or a complete set of three.
They are cheap but fine for infrequent use. I always reset them to minimum for storage.
1 -
NOTE the OP's specific need for torquing up Left Hand Threads…
Some (many) that can ratchet both ways only work to torque on RH threads…
e.g. that Teng tool, above, is NOT bi-directional (for torque) but will ratchet both ways see the pdf Documents file on the makers' site.
OP needs to double-check the one I suggested, although it seems it is OK for both thread types:
1 -
I think some are misunderstanding….
Getting it wrong could result in an expensive repair.
@Rodders53 are you the same as Avforums Rodders?
I'll look at your DeWalt suggestion.
Posting for 21 years...https://forums.moneysavingexpert.com/profile/27233/ohreally1 -
Not at all a heavy job more at the other end of the scale, if applying too much torque there is a very real danger of shearing.
Posting for 21 years...https://forums.moneysavingexpert.com/profile/27233/ohreally0 -
What sort of torque range are you needing ?
Heavyish as in general car work etc, 30 to 150 Nm, or electronics type use, 1 to 10 Nm ?
Never associate with idiots on their own level, because, being an intelligent man, you'll try to deal with them on their level - and on their level they'll beat you every time.
Being hated by idiots is the price you pay for not being one of them.
Jean Cocteau 1889-1963
1 -
-
Cheapest 1/4" drive push through type I could find:
2
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards



