📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Best beginners drill set

Options
2»

Comments

  • stuart45
    stuart45 Posts: 4,864 Forumite
    Sixth Anniversary 1,000 Posts Name Dropper
    One thing to keep in mind with SDS drills when going into a hard masonry wall is that it's not just about having a good drill bit.
    Using a drill of say 2J may not hammer into the wall hard enough and heat up the bit too much, whereas using one of 8 or 10J will go through a lot easier, even with a cheaper bit.
  • ic
    ic Posts: 3,430 Forumite
    Part of the Furniture 1,000 Posts Photogenic Name Dropper
    If in no rush, keep an eye on Lidl - they often do good DIY deals.  They have a 20V range of tools, which includes cordless drill drivers.  They'll normally stock accessories like drill bits at the same time as the drill.  Nice thing with their range is you can expand later and reuse the same batteries and chargers on other tools in the range.  I picked up a jigsaw, circular saw, sds and multisaw a few months ago.  Personally I have a good quality Dewalt drill with 4Ahr batteries - its the tool I use the most so was worth spending on - quite a step up from an old drill it replaced in terms of power, reduced size and longevity.
  • DPR87
    DPR87 Posts: 68 Forumite
    Fourth Anniversary 10 Posts Name Dropper
    I was in a similar position last year. Ended up getting up a Ryobi One Hammer drill which has been great for DIY jobs in my new house. Put up shelves, tv brackets etc drilling into wood, plasterboard and brick. Also used it to drill through lintel when putting up blinds. I think the most important thing for me was getting a good set of drill bits. Ended up with some Bosch ones which have been great. 
  • 531063
    531063 Posts: 285 Forumite
    Fifth Anniversary 100 Posts Name Dropper
    edited 20 March 2021 at 11:47AM
    As above the drill bits do most of the work
  • stuart45
    stuart45 Posts: 4,864 Forumite
    Sixth Anniversary 1,000 Posts Name Dropper
    It depends on how hard the wall is. My 2kg wont touch a Chert wall, just burns the tip, whereas the 5kg drill will go into it quite quickly with the same bit. The hammer action breaks up wall enough for the drill to cut through, unlike wood or metal where the bit does all the cutting.
  • daivid
    daivid Posts: 1,286 Forumite
    Part of the Furniture 1,000 Posts Name Dropper
    edited 20 March 2021 at 2:09PM
    If drilling into walls is going to be rare I wouldn't bother with a SDS drill. I have a previous incarnation of the Bosch combi linked in the 1st reply. It drills for wall plugs and has done 8mm pilots for core drilling. Last week it put a 16mm hole through through a double skin wall without any struggle, stepping up in 2mm intervals from an 8mm pilot hole. If I needed to do lots of such jobs I would weigh up buying or hiring a SDS drill (probably corded).
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 351K Banking & Borrowing
  • 253.1K Reduce Debt & Boost Income
  • 453.6K Spending & Discounts
  • 244.1K Work, Benefits & Business
  • 599K Mortgages, Homes & Bills
  • 177K Life & Family
  • 257.4K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 37.6K Read-Only Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.