Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Skirting - advice regarding gap between plaster and floor
bigsteve
Posts: 136 Forumite
Hi everyone,
I hope you can advise me on this matter.
I have arranged for an Amtico floor to be laid from the front door & hallway through to the kitchen to the back of the house by a professional fitter. It's going to be done in 2 bits - ply this weekend / flooring in a couple of weeks.
So all must be plyed throughout. In an effort to get the best ply surface possible I have removed the skirting from the hallway and the artchitrave from a doorway so the ply can fit right up to the walls
Now I have removed the skirting there is a gap between the (lathe & plaster) walls and the floor, where the skirting once was.
What to do about this gap?
I was going thinking of cleaning up the gap, PVA-ing the bricks and slapping some hardwall or something similar so the plaster meets the floor, in a reasonably level fashion.
The finish would not really matter, as I am going to put new skirting back, after the Amtico has been laid.
Would this be OK?
Would the hardwall be dry in enough in a couple of weeks?
Are there any better ways of doing this?
Can you forsee any pitfalls?
I'd appreciate your thoughts.
Cheers,
Steve
I hope you can advise me on this matter.
I have arranged for an Amtico floor to be laid from the front door & hallway through to the kitchen to the back of the house by a professional fitter. It's going to be done in 2 bits - ply this weekend / flooring in a couple of weeks.
So all must be plyed throughout. In an effort to get the best ply surface possible I have removed the skirting from the hallway and the artchitrave from a doorway so the ply can fit right up to the walls
Now I have removed the skirting there is a gap between the (lathe & plaster) walls and the floor, where the skirting once was.
What to do about this gap?
I was going thinking of cleaning up the gap, PVA-ing the bricks and slapping some hardwall or something similar so the plaster meets the floor, in a reasonably level fashion.
The finish would not really matter, as I am going to put new skirting back, after the Amtico has been laid.
Would this be OK?
Would the hardwall be dry in enough in a couple of weeks?
Are there any better ways of doing this?
Can you forsee any pitfalls?
I'd appreciate your thoughts.
Cheers,
Steve
0
Comments
-
Yes what you are suggesting will be fine.
Plenty of time for drying.
I use carlite bonding for this as it is well sticky and will stick to bricks and Laths.
Thats just personal choice though.
Be sure to pva and don't plaster right down to a concrete floor or any really.
Leave a 1/2 inch to an inch gap.
This will help when you replace skirtings.
I know you are not having carpets but if there is a big gap behind skirtings the carpet fitters tend to push the skirtings in when trying to get a snug fit.0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 355.9K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.2K Spending & Discounts
- 248.4K Work, Benefits & Business
- 606.1K Mortgages, Homes & Bills
- 179K Life & Family
- 263.9K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards