Reasonably priced brush for cutting in when painting?

Hello folks,

I have started to decorate the house again after a good number of years, and having trouble cutting in where wall meets ceiling etc.
Just find myself doing the cutting in a few times before its reasonable enough.

A lot of it is just down to my ability but possibly part of is to the cheap four for a pound brushes that I buy in pound shops.

I have read that it is very difficult to cut in with a bad brush, I have heard of painters paying upwards of £20 for one decent brush, well don't want to do that, but anyone know of a few decent brushes I can get say for around a fiver each?

Many Thanks.
«1

Comments

  • AndyMc.....
    AndyMc..... Posts: 3,248 Forumite
    1,000 Posts Combo Breaker
    They need to be worn in to cut in properly.
  • ColinFishwick
    ColinFishwick Posts: 1,391 Forumite
    I only use cheap brushes for jobs that I want to throw away brushes where a neat job isnt required. Other than that I use Harris no loss brushes they arent that expensive
  • getmore4less
    getmore4less Posts: 46,882 Forumite
    Part of the Furniture 10,000 Posts Name Dropper I've helped Parliament
    I got a 2" angled brush and got on really well with it.
    Think it was about £5-£6.
  • Cornucopia
    Cornucopia Posts: 16,440 Forumite
    Part of the Furniture 10,000 Posts Name Dropper Photogenic
    I have a 1 inch angled brush from Wilko. Was £1.50, I think.
  • Thanks a lot for replies. First time I have hard of angled paint brushes. I have googled a few pics, seems the bristles are at an angles instead of all being one length.


    If that is right how does this help in painting, and especially with cutting in?
    Thanks yet again.
  • flashg67
    flashg67 Posts: 4,118 Forumite
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    The angled bristles keep the head at the 'correct' and consistent angle to get a neat finish when cutting in. Same effect can be done with a standard brush with practice. I use a 2" or 3" brush for cutting in - Wilko's 'better' or 'best' range are decent for this and not too expensive. There is a reason the pros use expensive brushes though!
  • getmore4less
    getmore4less Posts: 46,882 Forumite
    Part of the Furniture 10,000 Posts Name Dropper I've helped Parliament
    The other thing I found was when I started I did not load the brush enough to do long uninterupted strokes.

    if doing 2 coats you get to practice 2-3 times.
    We also have coving which made it seem easier.
  • Apodemus
    Apodemus Posts: 3,410 Forumite
    Ninth Anniversary 1,000 Posts Name Dropper Combo Breaker
    You can, of course, cut a normal brush to shape if you don't have an angled one to-hand.
  • PDF
    PDF Posts: 179 Forumite
    Or use frog tape.
  • Norman_Castle
    Norman_Castle Posts: 11,871 Forumite
    Part of the Furniture 10,000 Posts Photogenic Name Dropper
    possibly part of is to the cheap four for a pound brushes that I buy in pound shops.
    A 25p brush is a stick with 50 poor quality bristles on the end.

    http://www.screwfix.com/p/hamilton-cutting-in-brush-2/7246p

    £3.29 divided by the number of rooms painted with it.
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 350K Banking & Borrowing
  • 252.7K Reduce Debt & Boost Income
  • 453.1K Spending & Discounts
  • 243K Work, Benefits & Business
  • 619.9K Mortgages, Homes & Bills
  • 176.4K Life & Family
  • 255.9K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 15.1K Coronavirus Support Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.