Car doesn't go into first gear properly since clutch change

jonj123
jonj123 Posts: 189 Forumite
edited 25 November 2013 at 6:14PM in Motoring
Hi

I recently changed my clutch and ever since I've had problem getting the car into first gear. Sometimes when I try putting it in first gear it seems like there is resistance and I have to put the gear back in neutral and try again. It is really frustrating specially at traffic lights. All other gears are fine and when the car has already gone into gear then it's OK changing gears. I took it back to garage where I got my clutch changed but the guy couldn't help.
Does anyone know what may be causing this please?

Many thanks

Car model: Toyota Aygo 08 reg.

Comments

  • paddedjohn
    paddedjohn Posts: 7,512 Forumite
    Part of the Furniture
    What car is it? It could be the gear linkage has been misaligned.
    Be Alert..........Britain needs lerts.
  • Iceweasel
    Iceweasel Posts: 4,874 Forumite
    Part of the Furniture 1,000 Posts Photogenic Combo Breaker
    Without knowing the exact make and model of car no-one can give a precise answer.

    However the clutch is not dis-engaging properly when you depress the pedal to the floor.

    Some cars have an adjustment rod on the hydraulic system.

    Others have a cable operated system - also with adjustment provision.

    Some have a adjustment free hydraulic set up and if you have that type then I would guess that the system has not been bled properly after the clutch change.

    Take it back and ask/insist firmly but politely that they check the adjustment and/or bleed the hydraulics.
  • jonj123
    jonj123 Posts: 189 Forumite
    paddedjohn wrote: »
    What car is it? It could be the gear linkage has been misaligned.

    Thanks for getting back, it's a Toyota Aygo 2008 model. If the linkage is misaligned it is possible that it only affects first gear?
  • Iceweasel
    Iceweasel Posts: 4,874 Forumite
    Part of the Furniture 1,000 Posts Photogenic Combo Breaker
    Is it difficult to engage reverse too?

    What happens if you try to move the lever into 2nd gear from stationary?
  • jonj123
    jonj123 Posts: 189 Forumite
    Iceweasel wrote: »
    Is it difficult to engage reverse too?

    What happens if you try to move the lever into 2nd gear from stationary?

    Reverse gear engages fine. Also if I put gear straight in 2nd from stationary it goes in fine. It's just when putting it in first gear that I have problems.

    P.s. sorry I forgot to mention it's a Toyota Aygo 08 model.
  • Iceweasel
    Iceweasel Posts: 4,874 Forumite
    Part of the Furniture 1,000 Posts Photogenic Combo Breaker
    OK then - I still think it's clutch adjustment.

    See here:

    http://www.toyotaownersclub.com/forums/topic/140241-clutch-pedal-adjustment/

    Take it back and see what they say.

    Don't accept a load of clap-trap about worn synchromesh!

    Good luck.
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 349.9K Banking & Borrowing
  • 252.6K Reduce Debt & Boost Income
  • 453K Spending & Discounts
  • 242.8K Work, Benefits & Business
  • 619.6K Mortgages, Homes & Bills
  • 176.4K Life & Family
  • 255.7K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 15.1K Coronavirus Support Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.