We're aware that some users are experiencing technical issues which the team are working to resolve. See the Community Noticeboard for more info. Thank you for your patience.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Canon IP90 Printer shows a constant Orange Light

Options
Hi Guys, advice needed.
I just turned my printer on, it flashed Orange, then Green.....but now shows a constant Orange light.
Even when i plug it out, it still has this dreaded orange light and no matter what i do it just does nothing!
Any advice greatly appreciated.

Comments

  • thor
    thor Posts: 5,504 Forumite
    Part of the Furniture 1,000 Posts
    When you say the orange light stays on even after 'unplugging', do you mean the power cable or the data cable?
    If I ever unplugged a (no battery) electrical device from the power supply and it still had a light on, I would get a bit spooked methinks.
  • Lol,...i meant the Data cable.;)
    Well my Brother pressed a couple of buttons and the printer works again, but still flashes Orange then Green.
    Something about the "Ink Absorber" flashed up but not a clue what that means (?)
  • santer_2
    santer_2 Posts: 4,406 Forumite
    1,000 Posts Combo Breaker
    edited 17 December 2012 at 12:57PM
  • dogmaryxx
    dogmaryxx Posts: 2,446 Forumite
    Part of the Furniture 1,000 Posts Name Dropper
    POWER lamp flashes alternate green and orange:
    An error that requires contacting a Canon service representative may have occurred.


    Disconnect the printer cable from the printer, and then turn the printer off and unplug the printer from the
    power supply for a while. Plug the printer back in and turn the printer back on.


    Manual
  • Tried all the Resets and stuff, but i'm still getting the flashing Orange light.
    It seems like the problem i'm having is below, which will probably cost loads.
    So maybe it's time for a new printer. :(
    Thanks for your advice Guys.

    Waste ink absorber almost full
    Ink used for cleaning is absorbed in a waste ink absorber placed in the printer. Eight flashes indicate that the waste ink absorber is nearly full. Press the RESUME/CANCEL button to cancel the error so that you can continue printing.
    Important
    If this error occurs, replacement of the waste ink absorber and maintenance of the printer are required. Canon recommends to contact a Canon service representative as soon as possible. Once the waste ink absorber becomes completely full, it cannot be printed until the Waste ink tank is exchanged.
  • santer_2
    santer_2 Posts: 4,406 Forumite
    1,000 Posts Combo Breaker
    You could check if they have any ideas here

    http://www.nifty-stuff.com/forum/viewforum.php?id=4
  • It gave up the ghost this morning.....totally dead.
    No lights came on at all, no matter what i pressed or plugged in & out...... nothing.
    Went out and bought a Brand new wireless Canon MG4150 for £49.99.
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 351K Banking & Borrowing
  • 253.1K Reduce Debt & Boost Income
  • 453.6K Spending & Discounts
  • 244K Work, Benefits & Business
  • 598.9K Mortgages, Homes & Bills
  • 176.9K Life & Family
  • 257.3K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 37.6K Read-Only Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.