📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Could XP update have killed PC motherboard?

Hi all,

My 73 year old Mum is a bit of a silver surfer and uses a PC for the web and writing the odd letter. Mum's PC is on its last legs - I have rebuilt it twice and the fan is again making a terrible noise (I have replaced this also once) so as I think it is probably not worth doing any more with it, I thought I would utilise a P4 PC installed with XP Pro spare.

This old but good PC had a blown power supply, thanks to a storm a couple of years ago so I purchased a replacement PSU and fitted it.

All worked great, but because the PC hadn't been switched on for a while, there were over 100 Windows updates to load. So I loaded them on and then had to shut down the PC down to finish loading the final 20. The updates seemed to work and the PC shut down.

I moved the PC into position in Mum's office (which is downstairs from my office so it wasn't too much of a rough journey) and plugged it all in, switched on and nothing - no power, completely dead.

I opened the PC back up and check connections which all seemed OK, took the power supply back to the shop who checked it but declared it OK, although they gave me a replacement anyway.

I have again brought this home, installed it and it is still dead.

Could the Windows update have killed the motherboard? Is there anything else I should be checking to determine what the problem could be? Thanks
:D Thanks to MSE, I am mortgage free!:D
«1

Comments

  • Spank
    Spank Posts: 1,751
    Tenth Anniversary 1,000 Posts Photogenic Name Dropper
    Forumite
    Your sure the socket works?
  • bod1467
    bod1467 Posts: 15,214 Forumite
    No software can kill a motherboard, only a physical influence. If the PSU had blown this likely took the mobo with it - not uncommon. In your case it likely was on the edge of going, and moving the PC was enough to tip it over.
  • angelavdavis
    angelavdavis Posts: 4,714
    Mortgage-free Glee!
    Forumite
    bod1467 wrote: »
    No software can kill a motherboard, only a physical influence. If the PSU had blown this likely took the mobo with it - not uncommon. In your case it likely was on the edge of going, and moving the PC was enough to tip it over.

    To be honest I didn't think so, I guess the move - however slight might have caused the issue, I guess I am just surprised the motherboard was good as gold for two days while I loaded the updates on it.
    Spank wrote: »
    Your sure the socket works?

    The socket seems to be powering the monitor OK, I also changed the power cable over a couple of times before I took it back to the shop so I know its not either the socket or power cables.
    :D Thanks to MSE, I am mortgage free!:D
  • Mista_C
    Mista_C Posts: 2,202
    Part of the Furniture Combo Breaker
    Forumite
    Probably obvious and I don't mean to insult your intelligence. Have you checked inside the case for loose screws/debris that can cause a short and prevent the computer from powering on?

    If they get under the motherboard they can wedge so you won't even hear them rattle.

    Failing that check that all the cards/memory/processor etc. are firmly in place and all clips are locked and tight.
  • GunJack
    GunJack Posts: 12,023
    Part of the Furniture 10,000 Posts Name Dropper Photogenic
    Forumite
    you did remember to connect the extra connector properly from the PSU to the mobo, along the main socket ?? It's often a 20+4 (i.e. two connectors), rather than just a single 24-pin one ?? Often with new PSUs you think you've got the sockets in tight, but 'c oz they're new (and therefore a tighter fit) you may not have quite got them clicked into place and hence with moving the box downstairs have managed to dislodge one ??
    ......Gettin' There, Wherever There is......

    I have a dodgy "i" key, so ignore spelling errors due to "i" issues, ...I blame Apple :D
  • esuhl
    esuhl Posts: 9,409
    Part of the Furniture 1,000 Posts Name Dropper
    Forumite
    And you've checked the fuse in the plug (and the power cable itself), right...?
  • ......and the switch on the back of the power supply (if it has one)!
  • Visiondvd
    Visiondvd Posts: 119 Forumite
    Yawn,ok this is longwinded but here it is. Do a visual check on all usb ports for damage, they if damaged can prevent mainboards from starting,bypass the on/off button on the case by shorting the two relevant pins(pwr) on the board with a screwdriver to verify the on/off button is ok or not. Still no starting , then consider this, left updating for two days? a p4 cpu/ seems really slow, so therefore would suggest really old outdated pc or dinosaur internet speeds, if not the case, then you have a fault with either cpu overheating, or bad ram, both would cause a mainboard to not start/power off or die.
    If it is really old, is it worth more than the price of a psu to repair?
    Also if old it will be hard to source a mainboard new.A guess for a socket 478 mb is about £50 new if you can find one.
    I suggest buying your mum a half decent used laptop.
  • Check the capacitors around the CPU socket. If they look like the picture below they're knackered and the cause of your woes - the tops of them should be completely flat and devoid of any dried liquid. Even if they're slightly domed they're knackered. The first time you'd be aware of an issue is when it didn't turn on again. Worst part is they cost pennies to buy but finding a computer shop with an actual real engineer who can use a soldering iron instead of a parts swapping monkey is quite hard.

    First picture is a good condition one. The following two are defective...

    cp4700-16v_ps.jpg

    748px-Elko-mit-ausgedr%C3%BCcktem-Gummistopfen.jpg

    Al-Elko-bad-caps-Wiki-07-02-17.jpg
  • angelavdavis
    angelavdavis Posts: 4,714
    Mortgage-free Glee!
    Forumite
    GunJack wrote: »
    you did remember to connect the extra connector properly from the PSU to the mobo, along the main socket ?? It's often a 20+4 (i.e. two connectors), rather than just a single 24-pin one ?? Often with new PSUs you think you've got the sockets in tight, but 'c oz they're new (and therefore a tighter fit) you may not have quite got them clicked into place and hence with moving the box downstairs have managed to dislodge one ??

    Thanks for this. I am pretty convinced they were connected OK. The PC is an older motherboard with a 20 pin connector only so you have to slide off the four extra pieces on the main connector. It then has a separate 2+2 which connects elsewhere on the board.

    I did all the obvious checks:

    -All connections to HDD, FDD, DVD, Motherboard - total of 2x4 pin connectors, small connector to FDD and 20 pin plus separate 4 pin connector to motherboard. These were initially connected and were all fine, PC worked in fact. I then disconnected, reconnected and replaced PSU and reconnected after the PC stopped powering up. My fingers are red raw from connecting and disconnecting the cables!

    -All screws were removed and put separately onto a dish so I could count them in and out.

    -I have replaced the power cable going into the PSU and plugged into different sockets in case it was something as simple as a fuse (I wish).

    -I have ensured the power switch at the rear of the PC is on (as it is a switched internal PSU).

    By the way, I am 17th edition domestic electric trained and trained and delivered IT software projects for 20 years - but I am by no means an IT hardware expert and definitely not an electronics expert!

    The updates took two days because I wasn't sitting in front of it to reboot, etc as necessary. Although the downloads took time because of the internet connection being not the speediest, the PC is actually pretty fast - especially for my Mum and has 2 Gb of RAM installed.

    Visiondvd - I checked online at a replacement value, it is still worth replacing the PSU and even a few more components before it ceases to become economically viable. I only stopped using it as my main PC myself because the Mhz are a bit low for the programmes I was running at the time. I will check out your other suggestions though, thanks

    I will also check out notmyrealname's recommendations on the capacitors. I have a soldering iron and ain't afraid to use it - I hate chucking stuff out if it still has potential life left in it). I have a spare laptop but Mum finds it too tricky to use, so it would be good to get this working.

    Thanks everyone for the suggestions.
    :D Thanks to MSE, I am mortgage free!:D
This discussion has been closed.
★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 356K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.3K Spending & Discounts
  • 248.5K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.