Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Disappointing wireless speeds - can anyone advise me?
Hungerdunger
Posts: 964
Forumite
I was given a Belkin N600 Modem Router for Christmas to replace my ageing Netgear DG 834. The main reasons were to be able to share a printer attached to it between our Desktop and Laptop and to be able to use my Laptop outside. (I'd been told that 820.11n offers better range than the Netgear's 802.11g.)
The laptop is usually used in the kitchen/living room which is about 6 metres away from the router but separated by a stone wall. As soon as we had set up the new router we noticed that web pages seemed to be taking longer to load than previously, even though our internet connection speed was the same as before - around 3.75 to 4Mbps.
I then tried a test copying a 250MB file from my Desktop PC (connected to the router by ethernet cable) to the Laptop. When the laptop was in the same room as the router the file transferred at around 4.5Mbps using the Belkin, and 2.7Mbps using the Netgear.
However when I moved the Laptop back to the kitchen, the speed using the Netgear dropped only a little to 2.6Mbps, while the Belkin dropped dramatically to around 1.6Mbps. In minutes and seconds the Netgear copied the file in 1:36, while the Belkin took 2:40.
What I need to know is:
1) Would you agree that the drop in performance of the Belkin is unacceptable (especially when the Netgear out-performed it).
2) Would this level of performance account for the slow loading web pages, or would that be something different?
3) Is there anything I can try to improve performance (Apart from knocking a hole in the wall!).
Should it help, the Belkin was connected at 65Mbps and the signal strength in the kitchen was "good". In the router setup, the Wireless channel is set to "Auto" and the Bandwidth is set to "20/40MHz"
The laptop is usually used in the kitchen/living room which is about 6 metres away from the router but separated by a stone wall. As soon as we had set up the new router we noticed that web pages seemed to be taking longer to load than previously, even though our internet connection speed was the same as before - around 3.75 to 4Mbps.
I then tried a test copying a 250MB file from my Desktop PC (connected to the router by ethernet cable) to the Laptop. When the laptop was in the same room as the router the file transferred at around 4.5Mbps using the Belkin, and 2.7Mbps using the Netgear.
However when I moved the Laptop back to the kitchen, the speed using the Netgear dropped only a little to 2.6Mbps, while the Belkin dropped dramatically to around 1.6Mbps. In minutes and seconds the Netgear copied the file in 1:36, while the Belkin took 2:40.
What I need to know is:
1) Would you agree that the drop in performance of the Belkin is unacceptable (especially when the Netgear out-performed it).
2) Would this level of performance account for the slow loading web pages, or would that be something different?
3) Is there anything I can try to improve performance (Apart from knocking a hole in the wall!).
Should it help, the Belkin was connected at 65Mbps and the signal strength in the kitchen was "good". In the router setup, the Wireless channel is set to "Auto" and the Bandwidth is set to "20/40MHz"
"The trouble with quotations on the Internet is that you never know whether they are genuine" - Charles Dickens
0
Comments
-
Try moving your new router slightly or turning it 90°.
Is it near anything metallic?
Stone walls aren't very good for Wi-Fi propagation.If my post hasn't helped you, then don't click the 'Thanks' button!
0 -
Change wifi channel from auto! I can't remember the name of the software, but it gives a breakdown of all the channels and any interference. A lot of routers will default to a small selection of channels, my speeds more than quadroupled just from altering to a channel with minimal interference.0
-
Are you using a N600 grade wifi link on the laptop? I am not very up on WiFi so may get shot down. However if the Belkin is doesn't have a seperate channel that copes with G standards then it will hunt for the right channels and waste speed. Furthermore if your laptop is still G then the Router will only work on G standards with it.New PV club member. 3.99kW system. Solar Edge with 14 x 285W JA Solar panels. 55° West from south and 35° pitch.0
-
Hungerdunger wrote: »2) Would this level of performance account for the slow loading web pages, or would that be something different?
3) Is there anything I can try to improve performance (Apart from knocking a hole in the wall!).
Should it help, the Belkin was connected at 65Mbps and the signal strength in the kitchen was "good". In the router setup, the Wireless channel is set to "Auto" and the Bandwidth is set to "20/40MHz"
2) No.
3) Change it from the default of Channel 1, 6 or 11 which most stuff seems to be on. Try 8 or 4 or 3.0 -
Thanks everyone for your replies. To answer various suggestions/questions:
The laptop is "n" enabled and connects on that protocol. I haven't tried changing the channel from Auto. But as there is only one other router close to us (we live down the end of a farm track with one other dwelling) would it make any difference? I had also tried moving the router and changing its angle without success
Having said all that, I've just repeated my test of moving a file between the two computers and this time I've had some better results, although the speeds appear to be very erratic, varying from a low of around 2MBps and one one occasion a much more respectable 7MBps. I'm not aware of making any changes other than re-starting the router.
Anyway, I'm off to bed now but will try some more tests tomorrow as well as having a good look at Inssider."The trouble with quotations on the Internet is that you never know whether they are genuine" - Charles Dickens0 -
Hungerdunger wrote: »Thanks everyone for your replies. To answer various suggestions/questions:
The laptop is "n" enabled and connects on that protocol. I haven't tried changing the channel from Auto. But as there is only one other router close to us (we live down the end of a farm track with one other dwelling) would it make any difference? I had also tried moving the router and changing its angle without success
There are many things that can cause interference to a wifi network:
microwaves, cordless phones, Bluetooth devices, wireless video cameras, wireless game controllers, fluorescent lights, etc.
So i would suggest changing the channel.0 -
Change the channel as advised. If that doesn't work, get a pair of Homeplugs.No free lunch, and no free laptop
0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards
