We're aware that some users are experiencing technical issues which the team are working to resolve. See the Community Noticeboard for more info. Thank you for your patience.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Advice fitting glass shelf in bathroom

Options
I thought I would ask this here as someone may even have put up this extact shelf...http://www.diy.com/diy/jsp/bq/nav.jsp?action=detail&amp;fh_secondid=11077755&amp;fh_view_size=10&amp;fh_eds=?&amp;fh_location=//catal!!!1/en_GB/categories<{9372014}/categories<{9372035}/categories<{9372170}/specificationsProductType=bathroom_shelves/featuresBrand=B\u0026Q&amp;isSearch=false

Any advice on installing and how you actually attach this to the wall. I can't see and screws on it.

Also, will I have to drill holes and if so what is the best way as I will be drilling into glazed tiles.

Since this is MSE I really don't want to buy anything extra although if I have to, I have to. eg Drill bits.

Many thanks for any advice.
C

Comments

  • tpt
    tpt Posts: 312 Forumite
    depending on the tiles (assuming they are ceramic). put some masking tape on the wall - this stops the bit slipping. Use a masonry drill, and turn off the hammer action on the drill (until your through the tile). Place drill where you want the hole and give the back of the drill a firm bang (makes a slight intendation that again stops the drill slipping)

    start the drill and keep the speed low to stop the drill heating up. bit of patience and you'll be through.

    if the tiles are porcelain - you'll need specialist bits. you'll know if they are porcelain after half an hour of drilling and no hole
  • flashg67
    flashg67 Posts: 4,128 Forumite
    Part of the Furniture 1,000 Posts Name Dropper Photogenic
    Your link didn't work for me but the screws are normally covered by a chrome 'trim' which either clips on or is secured with a concealed grub screw.

    Good advice from tpt - I've learned to my cost that patience is a virtue when drilling tiles. With luck and/or some compromise, you might find the grout lines line up for the screw holes which i have found easier to drill into
  • SailorSam
    SailorSam Posts: 22,754 Forumite
    10,000 Posts Combo Breaker
    Until you get through the tiles you're best starting with as small a drill bit as possible, this will slip less and you can go on to drill a larger hole afterwards.
    Liverpool is one of the wonders of Britain,
    What it may grow to in time, I know not what.

    Daniel Defoe: 1725.
  • flashg67 wrote: »
    Your link didn't work for me but the screws are normally covered by a chrome 'trim' which either clips on or is secured with a concealed grub screw.


    The shelf then slides into the trim between to plastic "buffers/jaws" and you turn a screw to clamp the glass in place.
    "If you act like an illiterate man, your learning will never stop... Being uneducated, you have no fear of the future.".....

    "big business is parasitic, like a mosquito, whereas I prefer the lighter touch, like that of a butterfly. "A butterfly can suck honey from the flower without damaging it," "Arunachalam Muruganantham
  • Thanks folks. Luckliy I have some spare tiles so if the tiles do crack I can replace them but hopefully it won't come to that ;-)

    Thanks everyone!!!
  • 27col
    27col Posts: 6,554 Forumite
    If you are drilling into tiles then you need a tile drill, not a masonry drill. Although the advice about putting tape on the tiles where you want to drill is good advice.
    I can afford anything that I want.
    Just so long as I don't want much.
  • Nukumai
    Nukumai Posts: 278 Forumite
    27col wrote: »
    If you are drilling into tiles then you need a tile drill, not a masonry drill.

    Using a tile bit is good advice. But a masonry bit will also do the job (unless the tiles are porcelain).
  • ormus
    ormus Posts: 42,714 Forumite
    ive used masonry drills in the past when i cant find the correct tile bit.
    no problems.
    drill slowly and let the bit do the work.
    (do not use hammer action).
    Get some gorm.
  • 27col
    27col Posts: 6,554 Forumite
    I agree, it is perfectly feasible to use a masonry drill. But the glass drill has a smaller and sharper point and is less likely to slip. As far as I'm concerned, whatever will do the job is ok by me. But generally I try to use the correct tool for any DIY job. I do hate to bodge it with the wrong tool if I can avoid it.
    I can afford anything that I want.
    Just so long as I don't want much.
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 351K Banking & Borrowing
  • 253.1K Reduce Debt & Boost Income
  • 453.6K Spending & Discounts
  • 244K Work, Benefits & Business
  • 599K Mortgages, Homes & Bills
  • 176.9K Life & Family
  • 257.4K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 37.6K Read-Only Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.