Advise on painting pre-primed MDF skirting

I've had all the architrave and skirting replaced in my new home.
It's all MDF

I think it's all pre-primed. It's white and has a slightly rough surface.

I want to paint it with Duluxe Diamond White Satinwood, which according to this forum will stay white, and not yellow.

Will i need to do anything to this MDF prior to painting, and will i need to use more than one coat?
Was a 40 a day smoker for 20 years.
Decided to give up, and haven't had a fag for 12 years.
Halfway through losing six stone.

Looking forward to early retirement.

Comments

  • markdavey
    markdavey Posts: 617 Forumite
    We have just had an extension completed with the same MDF pre-primed skirting.

    I did the following:

    Lightly rubbed down the skirting to remove the 'rough' patches (not too much or you'll remove the primer)
    2 coats of Dulux Professional Undercoat
    1 coat of Dulux Professional Gloss

    Am very pleased with the finish.
  • markdavey wrote: »
    We have just had an extension completed with the same MDF pre-primed skirting.

    I did the following:

    Lightly rubbed down the skirting to remove the 'rough' patches (not too much or you'll remove the primer)
    2 coats of Dulux Professional Undercoat
    1 coat of Dulux Professional Gloss

    Am very pleased with the finish.


    Wow, that's a lot of painting, i've got a whole house to paint:eek:
    Was a 40 a day smoker for 20 years.
    Decided to give up, and haven't had a fag for 12 years.
    Halfway through losing six stone.

    Looking forward to early retirement.
  • markdavey
    markdavey Posts: 617 Forumite
    You should be OK. the Dulux site says nothing about undercoating for Satinwood just primer (which is already done).
  • booty40uk
    booty40uk Posts: 514 Forumite
    I used this recently in my dining room. I simply filled and rubbed down the fixing holes and primed these areas. Then applied one coat of dulux satinwood and it looks great.

    HTH

    Andy
  • keystone
    keystone Posts: 10,916 Forumite
    Lightly it first with a medium grade abrasive to remove the rough bits. Then prime it again as you will have removed some of the primer. Go over it again with a very fine grade. Remove all dust. Satinwood can then go straight on. Mind you, I just hate the finish of satinwood but each to his own and its very easy to apply. Post #2 refers to a different finish and poster is 100% spot on if you are using gloss paint - but you ain't.

    Cheers
    The difference between genius and stupidity is that genius has it's limits. - Einstein
  • riverboat2001
    riverboat2001 Posts: 476 Forumite
    Debt-free and Proud! Mortgage-free Glee!
    Hi All,
    Well i was going with Satinwood, as a previous poster on here asked for a non yellowing paint for skirting etc.

    But still open to suggestions, we're not big DIYer's and don't paint every couple of years.

    So whatever goes up has to cope with the ocassional knock, and look good for 5+ years.

    I haven't bought the paint yet, but do intend to get a quality make, so any other ideas?
    Was a 40 a day smoker for 20 years.
    Decided to give up, and haven't had a fag for 12 years.
    Halfway through losing six stone.

    Looking forward to early retirement.
This discussion has been closed.
Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 349.7K Banking & Borrowing
  • 252.6K Reduce Debt & Boost Income
  • 452.9K Spending & Discounts
  • 242.6K Work, Benefits & Business
  • 619.4K Mortgages, Homes & Bills
  • 176.3K Life & Family
  • 255.5K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.1K Discuss & Feedback
  • 15.1K Coronavirus Support Boards

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.