We'd like to remind Forumites to please avoid political debate on the Forum... Read More »
We're aware that some users are experiencing technical issues which the team are working to resolve. See the Community Noticeboard for more info. Thank you for your patience.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Kitchen Design
Options
Comments
-
This kitchen is just too small, can you knock down the wall with the door in it?0
-
Howdens appliances are rubbish. Get yours from somewhere else, especially as when they inevitably go wrong, you'll spend months trying to get the warranty repair/replacements sorted.I could dream to wide extremes, I could do or die: I could yawn and be withdrawn and watch the world go by.Yup you are officially Rock n Roll0
-
Its always good to have other people's input, even if it is going to cost me money!
MX5 - No, there is no room the other side of the door. The hole house is small.
Jojo - I've heard that they're quite expensive as well, if I were to go with them, I would source my own.
Doozer - this chimney has been the bane of my life ! What do you think of this?0 -
Honey, if it's listed, you can't take it out without Listed Building Consent! Not even for the range. Listings don't just apply to the outside, they apply to the inside as well.
You might get permission to open it up, but I very much doubt that they'd consider letting you remove it.Everything that is supposed to be in heaven is already here on earth.
0 -
I've had someone round from the planning department and they ok'd me to remove it from the house, as long as the exterior stack remained and the fascia of the bit in the kitchen remained. Thats why I'm not going to remove it - but look for a solution to use it.. but I want to make it look nice at the same time ! Will get a structural engineer round to have a look, but what thickness of wall would you expect to have either side of the opening?0
-
Sorry to butt in on your thread, but am hoping someone can advise me too. I have the same units as shown on tobycgraham's kitchen pics and need to do some moving about to get rid of the fridge/freezer from the dining room. Can you use a normal larder housing unit (I have one already) to accommodate an integrated fridge or would I have to buy another housing unit specifically designed for integrated appliances? I'm hoping to put the huge fridge/freezer in the garage and just buy an integrated fridge for the kitchen.
Also - could I house a washing machine in a normal larder unit too or would I have to buy a new machine and integrated cabinet (worried about movement of machine when in spin)? Hope someone can help. Have next to zero cash to do this, so if I can re-use what I already have then that would be brilliant.0 -
You don't need a new tower for a fridge freezer - you can take the shelves out. The only problem you might have is if the doors on your larder unit don't match up with the heights on the fridge freezer. Fridge freezers vary because some people like more fridge space, others 50/50 so you order the doors to match the f/f.
Washing machines don't fit into a unit at all, you buy a special door for them.
toby, I'm sure I replied to your last post?! I said panic over about the PP and that I honestly didn't know what you would want to hold it up - as much a possible really! The structural engineer will probably know just by looking at it. Post back when you've cleared that area!Everything that is supposed to be in heaven is already here on earth.
0 -
Doozergirl wrote: »You don't need a new tower for a fridge freezer - you can take the shelves out. The only problem you might have is if the doors on your larder unit don't match up with the heights on the fridge freezer. Fridge freezers vary because some people like more fridge space, others 50/50 so you order the doors to match the f/f.
Washing machines don't fit into a unit at all, you buy a special door for them.
toby, I'm sure I replied to your last post?! I said panic over about the PP and that I honestly didn't know what you would want to hold it up - as much a possible really! The structural engineer will probably know just by looking at it. Post back when you've cleared that area!
Thank you for your reply, it's much appreciated!!! (and now I can have a think about what the possibilities are...and what to get!)0 -
Right, stage one is now complete:
How would you proceed with the design? I'm still thinking about a range, mainly because I'm not sure if a standard cooker will look right inside the chimney.0 -
I know it's not quite the same as here the chimney breast has been partially removed (not by us, I hasten to add!), but when we did the kitchen in our previous house we didn't put in a range - I didn't like the idea of grease etc being able to hide around it - but by placing the hob and the built-in oven within the chimney breast "area" I think it sort of looks like a range...
(Hope this link works)
http://www.flickr.com/photos/22737238@N00/2558665473/sizes/z/in/set-72157605484281366/
Plus we could then put the extractor hood inside the chimney breast.0
This discussion has been closed.
Confirm your email address to Create Threads and Reply

Categories
- All Categories
- 351K Banking & Borrowing
- 253.1K Reduce Debt & Boost Income
- 453.6K Spending & Discounts
- 244K Work, Benefits & Business
- 598.9K Mortgages, Homes & Bills
- 176.9K Life & Family
- 257.3K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.1K Discuss & Feedback
- 37.6K Read-Only Boards