Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Cordless home phone struggling to ring
loopa1
Posts: 81 Forumite
Hi all
We recently bought new phones for our landline. We went with the BT Freelance XD7500 (twin pack).
I set the phones up as the instruction manual stated (charging the phones for 24hrs before use etc.) but then when we tested the phones, they didn't ring properly.
Hard to explain what happened on an internet forum...but think of it this way, instead of repeating "ring-ring", it would go "ri...ring.....ring-ring....ri....ri....) and so on - the ring pattern would be inconsistant. Sometime you'd hear the initial beep for the first ring, but then you wouldn't hear the phone ring anymore.
I phoned BT's helpline and they told me to reset the phones and try again. I did this, but it made no difference. Assuming the phones were faulty, I took them back and got another model - the BT Graphite 2500 (twin).
However, same thing happens. Thinking I might be suffering from interference from my wi-fi, I switched it off and tried the phones, but still, no difference. When we're on the phone, the reception is fine, so surely it's not a phoneline strength issue?
My phoneline is supplied by Virgin Media...but surely that wouldn't make a difference would it? And my broadband/TV comes in to the house seperately via their coaxial cable.
Any suggestions?
We recently bought new phones for our landline. We went with the BT Freelance XD7500 (twin pack).
I set the phones up as the instruction manual stated (charging the phones for 24hrs before use etc.) but then when we tested the phones, they didn't ring properly.
Hard to explain what happened on an internet forum...but think of it this way, instead of repeating "ring-ring", it would go "ri...ring.....ring-ring....ri....ri....) and so on - the ring pattern would be inconsistant. Sometime you'd hear the initial beep for the first ring, but then you wouldn't hear the phone ring anymore.
I phoned BT's helpline and they told me to reset the phones and try again. I did this, but it made no difference. Assuming the phones were faulty, I took them back and got another model - the BT Graphite 2500 (twin).
However, same thing happens. Thinking I might be suffering from interference from my wi-fi, I switched it off and tried the phones, but still, no difference. When we're on the phone, the reception is fine, so surely it's not a phoneline strength issue?
My phoneline is supplied by Virgin Media...but surely that wouldn't make a difference would it? And my broadband/TV comes in to the house seperately via their coaxial cable.
Any suggestions?
0
Comments
-
Have you tried changing Headset and base ringer melody Page 21 or section 21 not sure exact location0
-
Yes - at first I thought I'd somehow set these up wrong so that they were conflicting, but there's nothing in the manual to suggest I've set-up anything incorrectly.
The internal rings work fine by the way - it's just when it's an incoming external call.0 -
Ok - I disconnected the batteries for my 2nd handset, and the other phone rang fine when my setup thought there was only one phone.
But as soon as I put the batteries back in, back to square one. I've been searching the internet for similar problems and they exist...and some people seem to be quoting ringer equivalence numbers (REN).
I think these two modern handsets should have a REN of less than two (less than one each), and I'm wondering if the socket my 'base' phone is plugged in to can't handle this. My 'base' socket also feeds another socket upstairs - so possibly something to do with how this has been wired (by previous home owner or technician presumably)?0 -
Maximum REN should be no more than 4. If the total REN of all your phones added together is 4 or more then you'll get problems. It's best to keep it below 4 if you can.0
-
I presume the old phones rang OK?
Having more than one wireless handset active shouldn't affect the REN as only the base unit connects to the line. It seems very strange to me that it makes any difference at all.
I guess being on VM you don't have any ADSL filters but if you could borrow one from somebody and plug it in then that will in effect replace the ring capacitor in the master socket as each filter has its own. It isn't necessarily going to fix anything but if it does then work it indicates a faulty master socket.
Please confirm that you are using the phone cord that came with the set and directly into your socket as a dodgy extension lead may cause a problem.0 -
I understand the point about REN, but how are you supposed to know if you're over or under 4? Unless I knew what REN my handsets have, I can't work it out.
The old phones worked fine. We had two corded phones, both were pluged in to phone sockets - one downstairs and one upstairs.
Nope, no ADSL filters, I can borrow one from work tomorrow and try it out. And yes, phone cord that came with the handsets is being used - plugged straight from the base to the phone socket with no extensions.0 -
The REN number should be marked on the label on the base of the phone.0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 356K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.3K Spending & Discounts
- 248.5K Work, Benefits & Business
- 606.2K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards