📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!

Engine overheating/Heaters Cold/Losing Water

24

Comments

  • motorguy
    motorguy Posts: 22,650
    Part of the Furniture 10,000 Posts Name Dropper
    Forumite
    If the head gasket has now now gone for a second time, you'll probably be best scrapping the car OR forking out for another engine.
  • atrixblue.-MFR-.
    atrixblue.-MFR-. Posts: 6,887 Forumite
    edited 20 October 2010 at 4:04PM
    pgilc1 wrote: »
    If the head gasket has now now gone for a second time, you'll probably be best scrapping the car OR forking out for another engine.
    not necessary to scrap or buy a recon engine!
    eventhough rover has nutoriously made a mistake with the HG's the rest of the engine is solid and will take a battering including overheating.

    yes the head will most certainly need scimming and a pressure test due to the overheat you dont know if it has caused a hairline crack in the head.

    the developers of headsets these days have come a long way in stopping these headgasgets from blowing again,
    GUG701125HS.JPGthis is the old type headset note on the headgasket there are red rubber seals this has been replaced.Land_Rover_Head_Gasket1.jpgthis is the newer type made of multi-layered steal. used in conjunction with a headsaver (a sheet of metal to replace the skimmed layer off the head laid on the piston side under the headgasket) will prevent this from happening again. BGA Automotive develop these gasket sets and are not overly priced at around £30-£50 with headbolts.
  • Doooford
    Doooford Posts: 471 Forumite
    Just to update you all. Thanks for all of your advice but the head gasket did go and left me stuck on the hard shoulder near Leicester with the AA refusing to take me home as they could only recover me upto 50 miles (The full journey wuld cost £250 at £2 a mile plus fees) and the hire car that I was entitled to wasn't available until 8am the following day as my licence was away getting the photo updated with the DVLA. (rant over)

    I now have a Rover 75 with a BMW Diesel engine and all is well again.
  • of course the head gasket went its a rover
  • Inactive
    Inactive Posts: 14,509 Forumite
    of course the head gasket went its a rover

    Indeed, but then the OP buys another Rover.. OK it has the BMW engine, but it is still a Rover ..
  • i think the BMW engine might pop a gasket in protest and feel emotionally insulted at being bolted into such a beast
  • Gloomendoom
    Gloomendoom Posts: 16,551
    Part of the Furniture 10,000 Posts Combo Breaker
    Forumite
    Doooford wrote: »
    Just to update you all. Thanks for all of your advice but the head gasket did go and left me stuck on the hard shoulder near Leicester with the AA refusing to take me home as they could only recover me upto 50 miles (The full journey wuld cost £250 at £2 a mile plus fees) and the hire car that I was entitled to wasn't available until 8am the following day as my licence was away getting the photo updated with the DVLA. (rant over)

    I now have a Rover 75 with a BMW Diesel engine and all is well again.

    Good choice. This link might be of interest.

    You were unlucky with the 420. That engine is usually trouble free.
  • bigjl
    bigjl Posts: 6,457 Forumite
    Inactive wrote: »
    Indeed, but then the OP buys another Rover.. OK it has the BMW engine, but it is still a Rover ..


    The Rover 75 with a diesel engine is a very reliable car, with the advantage of not being a BMW.

    The new fix for the K-series engine, financed by the Chinese, also includes a new oil rail and head bolts.

    The problem with the K series was due to lack of investment the Rover engineers had to modify the small, 1.1 K series engine to make it bigger, to do this they went from a closed deck block to an open one, the issue was simply the fact that the head bolts went all the way from the head to the oil rail rather than fixing into the head itself, so in effect the block was sandwiched between the head and oil rail.

    Indeed you are unlucky to have aproblem with the 2.0 as it wasn't a K series engine, and was actually more like the T series engine as fitted to the 620 Ti and 820 Vitesse Turbo.

    From what you have said you had a flow issue, blockage or a leak causing the level to drop to the point that the heater doesn't work any more.

    Any car used for any significant period with such an issue will eventually overheat.


    The simple fact is that the Chinese owners of everything that was Rover have financed a proper fix to the issue, they have found the engine to be actually fairly modern and efficent, so have used more recent engineering technology to correct the problem caused by the lack of investment at Rover.

    It is sad that British people are happy to attack a compay that was killed through lack of investment and cherry picking.

    Don't worry though the money was well spent in the welfare state.
  • they would have been better picking cherries

    i wouldnt mind a metro 6r4 ;)

    think rover tried to copy the indy car engines method of casting with open blocks and damp/wet liners and it didnt work out to well
  • Inactive
    Inactive Posts: 14,509 Forumite
    Rover made rubbish cars, that is why they went to the wall...end of.
This discussion has been closed.
★ ★ ★ Meet your Ambassadors

🚀 Getting Started

Hi new member!

Our Getting Started Guide will help you get the most out of the Forum

Categories

  • All Categories
  • 355.9K Banking & Borrowing
  • 255K Reduce Debt & Boost Income
  • 456.2K Spending & Discounts
  • 248.4K Work, Benefits & Business
  • 606.2K Mortgages, Homes & Bills
  • 179.1K Life & Family
  • 264K Travel & Transport
  • 1.5M Hobbies & Leisure
  • 16.2K Discuss & Feedback
  • 37.7K Read-Only Boards
Quick Search

Is this how you want to be seen?

We see you are using a default avatar. It takes only a few seconds to pick a picture.