We’d like to remind Forumites to please avoid political debate on the Forum.
This is to keep it a safe and useful space for MoneySaving discussions. Threads that are – or become – political in nature may be removed in line with the Forum’s rules. Thank you for your understanding.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Pointing Chimney Breast
OohSoHolly
Posts: 358 Forumite
Hello,
Hoping someone can help me with this worrying job we have yet to tackle.
Basically we bought a house in September last year which had a log burner located in the dining room. We were informed that all that it needed was sweeping however as with all jobs it wasn't this simple. So we discovered it needed a new register plate and flute and to cut a long story short there was a random wall built around it that would prevent us from having this done. So we've taken that wall down to reveal the original Chimney breadt however it needs re-pointing.
We're looking to do this while we're off this week however when we uncovered it there were some cracks in the mortar and some hairline cracks in the bricks. We're really concerned now that when we go to remove the mortar the bricks are going to shift or potentially the whole thing could collapse.
I've attached some photographs and would really appreciate some views and advice on this. It's our first house so all jobs are unnerving to us!
Many Thanks
Hoping someone can help me with this worrying job we have yet to tackle.
Basically we bought a house in September last year which had a log burner located in the dining room. We were informed that all that it needed was sweeping however as with all jobs it wasn't this simple. So we discovered it needed a new register plate and flute and to cut a long story short there was a random wall built around it that would prevent us from having this done. So we've taken that wall down to reveal the original Chimney breadt however it needs re-pointing.
We're looking to do this while we're off this week however when we uncovered it there were some cracks in the mortar and some hairline cracks in the bricks. We're really concerned now that when we go to remove the mortar the bricks are going to shift or potentially the whole thing could collapse.
I've attached some photographs and would really appreciate some views and advice on this. It's our first house so all jobs are unnerving to us!
Many Thanks
0
Comments
-
I have seen far worse , The arch looks fine you always get some shrinkage with chimney breasts. When you rake out the joints some of the bricks may get loose they can be taken out and relayed. Just take your time and there should be nothing to worry about.0
-
I have seen far worse
Did some work on my chimney breast last year - The bricks in the arch looked decidedly dodgy, and when I poked one, the entire arch collapsed :eek: It was only a very rusty bit of 3/8" thick iron bar that had been holding the whole lot up. Quickly got an acro & strongboy in there to support everything whilst the arch was replaced.Any language construct that forces such insanity in this case should be abandoned without regrets. –
Erik Aronesty, 2014
Treasure the moments that you have. Savour them for as long as you can for they will never come back again.0 -
Oh No, we just went from incredibly relieved to incredibly terrified again! :eek:0
-
It will be fine; see those cracks in a triangle? Worst case scenario, that would fall out. That's most likely not going to happen, and you can crack on with the pointing.
I would not be concerned.0 -
OohSoHolly wrote: »Oh No, we just went from incredibly relieved to incredibly terrified again! :eek:
My brickwork was considerably worse than yours. It was only the arch and a couple or three courses of bricks that fell down. The rest of the chimney breast remained standing, and I probably didn't need the acro/strongboy (but it made me feel safer).
As for your brickwork, I would suggest cutting a template out of something like MDF to the same shape as the brick arch (cut two pieces), and then build some supporting framework out of 3x2 timber. Once it is wedged in place, taking bricks out of the arch won't see it all collapsing around your ears.Any language construct that forces such insanity in this case should be abandoned without regrets. –
Erik Aronesty, 2014
Treasure the moments that you have. Savour them for as long as you can for they will never come back again.0 -
There seems to be a good supporting radius on the arch and I would not expect to have to remove any bricks.
As already mentioned above the interlocking effect (corbelling) of the brickwork above the arch means that very little is at risk of collapse.
I would grind out the bad jointing as far back as possible and repoint with a 4:1 sand/cement mortar.Forgotten but not gone.0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 352.3K Banking & Borrowing
- 253.7K Reduce Debt & Boost Income
- 454.4K Spending & Discounts
- 245.3K Work, Benefits & Business
- 601.1K Mortgages, Homes & Bills
- 177.6K Life & Family
- 259.2K Travel & Transport
- 1.5M Hobbies & Leisure
- 16K Discuss & Feedback
- 37.7K Read-Only Boards