Ready, steady… save!
You don’t need a chart to join in. Here are 2 ways to record your savings:
1. Cross it off
Pop a chart into your first post. Saved an amount? Cross it out! Read more »
£0.01 £0.02 £0.03
2. Write it down
Skip the chart and add updates to your first post. Read more »
“Another +£3 saved today. Go me!”
Use +£ before each new saving so it counts towards your total.
📨 Have you signed up to the Forum's new Email Digest yet? Get a selection of trending threads sent straight to your inbox daily, weekly or monthly!
Simple/cheap Import/ Export monitor
Rheumatoid
Posts: 1,146
Forumite
I can see my generation on my Geo solo II but it would be useful to see when I am importing or exporting. Is there such a thing or do the usual things just monitor flow of electricity and can't show you which way it is going?
TIA
R
TIA
R
0
Comments
-
The_Green_Hornet wrote: »
thanks but was hoping for something a bit less than £800 -
HiRheumatoid wrote: »thanks but was hoping for something a bit less than £80
If you have the ability to place the clamp sensor on the house feed then you'd be able to see load, so with 2 basic monitors you could see generation & load - so it just comes down to your mental arithmetic ...
HTH
Z"We are what we repeatedly do, excellence then is not an act, but a habit. " ...... Aristotle
0 -
Hi
If you have the ability to place the clamp sensor on the house feed then you'd be able to see load, so with 2 basic monitors you could see generation & load - so it just comes down to your mental arithmetic ...
HTH
Z
Thanks but would there not still be some degree of doubt as to what is showing on the clamp meter is coming in or going out? Or do they only ever measure what is coming in and would be at zero if its going out. Excuse my thickness
0 -
HiRheumatoid wrote: »Thanks but would there not still be some degree of doubt as to what is showing on the clamp meter is coming in or going out? Or do they only ever measure what is coming in and would be at zero if its going out. Excuse my thickness
It all depends on how your solar has been tied into the mains ...
Ours is connected to it's own distribution box which is connected to the main feed via a Henley-block ...
Meter --C-- HB ---A--- Fuse
>House
|
B--- Fuse
TGM
PV
If you have this setup then clamps measure
A - House load
B - PV Gen
C - Net Import/Export (but which direction not known)
If not then you'll likely have C -or- B&C, in which case a clamp monitor system which can distinguish AC flow (like the one DaveF built!) or dedicated kit would be needed.
HTH
Z"We are what we repeatedly do, excellence then is not an act, but a habit. " ...... Aristotle
0 -
Thanks but have no idea about that. all Greek to me
0 -
So our mains comes in, through the meter then split to two consumer units, one is the 'original house', the other is the garage. The garage one then has the PV connected.
So we can measure what the original house consumer unit uses and what the garage plus pv unit uses but of course we don't know the breakdown by direction of the flow between the garage and the junction next to the import meter is.I think....0 -
I'm working on this at the moment plan to use 2 clamps one on the solar inverter the other an the house feed
Then use an adrino or raspberry pi to do the calc and output to a web page0 -
hi
If you have a henley block use to owl meters very cheap.
was free years ago from your leccy supplier.
Fit one to the solar feed and one to leccy in feed.
regards
gefnew0 -
Hi
Or search for Dave Fowler he has a mdified version of the owl that does both.
regards
gefnew0
This discussion has been closed.
Confirm your email address to Create Threads and Reply
Categories
- All Categories
- 355.9K Banking & Borrowing
- 255K Reduce Debt & Boost Income
- 456.2K Spending & Discounts
- 248.4K Work, Benefits & Business
- 606.1K Mortgages, Homes & Bills
- 179.1K Life & Family
- 264K Travel & Transport
- 1.5M Hobbies & Leisure
- 16.2K Discuss & Feedback
- 37.7K Read-Only Boards

